[Group] Super Four Non-VTEC Family: PB1 VerR & VerS

[zanwoocheh]

Hi all

seems like after the fall, my fork start to leak oil onto the floor, maybe i know is it serious? and whats the repair dmg like???

thankssss

Where is the oil from? the base of the fork? or the middle part where the suspension activities are? of course its dangerous. the oil will travel to your front wheel... might cause urself serious injuries.

Hw much dmg depends. Is there a dent / scratch on the chrome fork near the seal? Its the chrome surface where it penetrates.

Otherwise, just a change of fork seal wld do..

[zanwoocheh]

Aiya... y nobody keen on my voltmeter...lol
Similar in sizing to the common MR Gauge....
Brand under MB electronic....

Cash & carry $18 all year round...

For all S4, since Iam riding 1 ... $17 only
ONLY APPLICABLE TO CB400 ONLY ALL YEARS!!!

Cheers!!!!

Any enquiries just feel free to buzz me.... or click on my siggy...

Thank Steven for the Voltmeter.

Look forward for more accessories..

[speedaddict]

Steven where can I see the list of stuff u have for ver S?

[GhostBiker]

hi fellow riders, anyone experienced probs with their speedometer? mine is Version S original (red color digits)
when i ride between 80km/h and 100km/h, i can see the speedo needle fluctuating by itself unstably, sometimes if i ride at 90-95, the needle always stay at 80km/h, only upon accelerating beyond 95km/h, the needle starts to move, but drops back to 80 immediately if i cruise. thanks in advance for any kind advise.

Ghost.

[tionghan]

hi everyone.. just gotta myself a ver s .. thing is .. when i throttle hard.. got white smoke.. heard that its quite serious . . any rectification to that?
also does ah pek do top overhaul kinda thingy?

[tionghan]

double post

[stwb1981]

Thank Steven for the Voltmeter.

Look forward for more accessories..

thanks mate

Steven where can I see the list of stuff u have for ver S?

hi mate...
been busy for these past week hence nt log in for quite a while...
not alot of stuff but will post in this thread no worries....
Cheers

hi fellow riders, anyone experienced probs with their speedometer? mine is Version S original (red color digits)
when i ride between 80km/h and 100km/h, i can see the speedo needle fluctuating by itself unstably, sometimes if i ride at 90-95, the needle always stay at 80km/h, only upon accelerating beyond 95km/h, the needle starts to move, but drops back to 80 immediately if i cruise. thanks in advance for any kind advise.

Ghost.

if small case speedo cable change..
but likely yr spring in the meter nt very gd liao...

hi everyone.. just gotta myself a ver s .. thing is .. when i throttle hard.. got white smoke.. heard that its quite serious . . any rectification to that?
also does ah pek do top overhaul kinda thingy?

hmm.... doesn't sound gd...
u gt to check wif ah Pek then....

[GhostBiker]

thanks mate







if small case speedo cable change..
but likely yr spring in the meter nt very gd liao...

anyone replaced the meter before? i googled and found out it usually comes in a set consisting of the speedo, tacho and indicator lights. tentatively, my mechanic says need to replace the speedo meter only, not the whole set. well, if its only replacing the speedo cable, i'm fine with it, but if need to replace the whole thing, its going to cost me more than $200

[}STRYKER{]

thanks mate



hi mate...
been busy for these past week hence nt log in for quite a while...
not alot of stuff but will post in this thread no worries....
Cheers



if small case speedo cable change..
but likely yr spring in the meter nt very gd liao...




hmm.... doesn't sound gd...
u gt to check wif ah Pek then....

Bro, my fren tried to call u to get ur volt meter but he cant get u.
Ur no at moto bici adv still same rite?will ask him to call u again tomolo can?


}STRYKER{ sent this post via iPhone using Tapatalk

[}STRYKER{]

anyone replaced the meter before? i googled and found out it usually comes in a set consisting of the speedo, tacho and indicator lights. tentatively, my mechanic says need to replace the speedo meter only, not the whole set. well, if its only replacing the speedo cable, i'm fine with it, but if need to replace the whole thing, its going to cost me more than $200

Bro i still have the stock speedo for ver s. If im not wrong, my rpm meter only spoilt but i change to a chiong meter bought from ebay for abt $150 two yrs back..if u want just the speedo meter assembly,i cn sell u the whole meter.u can test it first before buying.


}STRYKER{ sent this post via iPhone using Tapatalk

[stwb1981]

anyone replaced the meter before? i googled and found out it usually comes in a set consisting of the speedo, tacho and indicator lights. tentatively, my mechanic says need to replace the speedo meter only, not the whole set. well, if its only replacing the speedo cable, i'm fine with it, but if need to replace the whole thing, its going to cost me more than $200

Hmm try FJT...
I brought my Blackbird speedo meter oso fr there juz the speedo...
but it cost me $250 lah....lol
if nt get MIC Meter set aka chong de lah...

Bro, my fren tried to call u to get ur volt meter but he cant get u.
Ur no at moto bici adv still same rite?will ask him to call u again tomolo can?


}STRYKER{ sent this post via iPhone using Tapatalk

My apologises mate...
was out of town & oso out of hp recep area hence unable to contact...

num still the same if nt can always contact my bro aka partner Allen @ 98729296
Mine same 96284016...

Nonetheless will be rolling out some S4 accessories & spares soon...
do stay tune...

Will post a list here as well mates

Cheers!!!

[badd89]

guys...need help..any1 of u guys know where i can get my hands on the nuts that are on our brake calipers??? the alen key type.. mine has rusted and would like to get it change.. any1 knows where to get it and roughly how much..tq

[}STRYKER{]

guys...need help..any1 of u guys know where i can get my hands on the nuts that are on our brake calipers??? the alen key type.. mine has rusted and would like to get it change.. any1 knows where to get it and roughly how much..tq

I believe its called a set screw. U can try those hardware shops selling bolts n nuts...there's one along amk ave 3 just before caltex and another at shun li industrial park at kaki bukit area...west side not sure.


}STRYKER{ sent this post via iPhone using Tapatalk

[badd89]

BY any chance any1 know what to say to the shop??hehe quit dumb when it comes to the nuts...thankz!

[Ah Pek]

BY any chance any1 know what to say to the shop??hehe quit dumb when it comes to the nuts...thankz!

You won't find the exact replacement type..its a "mushroom head" allen key type size 6( I think). The best is to take off one sample so that they know the length (most important) and diameter. Properably they will jive u the round head allen key type and with a seperate washer. Original has to order from Boon Siew.

[}STRYKER{]

BY any chance any1 know what to say to the shop??hehe quit dumb when it comes to the nuts...thankz!

Bro try take a pix of the screw...i c if i can find it at my werk place or have seen it some where...


}STRYKER{ sent this post via iPhone using Tapatalk

[stwb1981]

BY any chance any1 know what to say to the shop??hehe quit dumb when it comes to the nuts...thankz!

if want to save the hassle, folow me to Msia...

They will install for u as well....

should be RM2-RM3 per bolt depends on lenght...

Stainless steel...

Good point of going in... save the hassle of fixing, or thinking what size...
Bad point more expensive... if buy from those screw shop they are much cheaper CONFIRM!!!

For all stainless steel bolts & buts etc....
Go to shun li industrial park...

Joo Metal Pte Ltd
No 73 kaki bukit ave 1
Shun Li industrial park
S417949

as spoken by the others U nid to have the size & measurement if nt bring a smaple down like what i always do..lol

[exwhyzee]

if want to save the hassle, folow me to Msia...

They will install for u as well....

should be RM2-RM3 per bolt depends on lenght...

Stainless steel...

Good point of going in... save the hassle of fixing, or thinking what size...
Bad point more expensive... if buy from those screw shop they are much cheaper CONFIRM!!!

Bro at jb there got colored ones or not? Looking for a few red or black bolts/nuts for my bike(radiator,footrest bracket,side panels etc.)...evotech & probolt too expensive lah

[stwb1981]

Bro at jb there got colored ones or not? Looking for a few red or black bolts/nuts for my bike(radiator,footrest bracket,side panels etc.)...evotech & probolt too expensive lah

Hi mate....

Personally, i feel those colour bolts are not strong enuf hence i nv enquire abt them...
To me, durability is of upmost impt hence stainless steel bolts..

Thye may have but dun quote me though

[iMustik]

Hi bros, anyone change the ignotion set before?? Im riding a vers s... I lost my masterkeys for my ignition, fuel cap and seat lock... Die die!! Any suggestions??

[exwhyzee]

Hi mate....

Personally, i feel those colour bolts are not strong enuf hence i nv enquire abt them...
To me, durability is of upmost impt hence stainless steel bolts..

Thye may have but dun quote me though

Oh ok noted


Anyway anyone here ever went to scrapyard to look for items? Gone thru the search function and 2 prominent scrapyards in sungei kadut came up but they are usually associated with items for small bikes...looking for extra brake n clutch levers and steering yoke (triple clamp?) for version s n maybe a showa shocks or ss headers...will give the above-mentioned scrpyards a try though..

anyone willing to share their experience with scrapyards?

[mark1979]

For cb400 rear showa shock
Add spacer for hard
Interested people pls SMS me...
Not for fussy people...thanks.
Untuk mengetahui maklumat yang lebih lanjut...
Sila SMS me. 8l22,8o82

[ProFatSir]

Hi bros, anyone change the ignotion set before?? Im riding a vers s... I lost my masterkeys for my ignition, fuel cap and seat lock... Die die!! Any suggestions??

do you have any spare key?
cheapest way is to use alarm lock so that you do not need to change the whole set as it would be expensive.

sent from my Ericsson GH388.

[wilson24]

if anyone have a front mudguard for sale..pm me..thanks

[stwb1981]

Hi bros, anyone change the ignotion set before?? Im riding a vers s... I lost my masterkeys for my ignition, fuel cap and seat lock... Die die!! Any suggestions??

hmm...

Ver S rite...
lost key no worries as no nid change cdi...

I gt spare iginition lock ,seat lock & fuel tank lock... but all using diff keys...
http://www.singaporebikes.com/forums...it-From-My-PB1
If on budget get tis fr me...
available stock... used but nt abused dekit fr my pb1 pricing neg....

If u wan i have MIC lock set which i am using now....
All locks using 1 key to open...
Brand new set...
Pricing firm @ $100
Gt to wait though as i yet to bring them in....

Call me for more info...
Steven @ 96284016

[stwb1981]

Oh ok noted


Anyway anyone here ever went to scrapyard to look for items? Gone thru the search function and 2 prominent scrapyards in sungei kadut came up but they are usually associated with items for small bikes...looking for extra brake n clutch levers and steering yoke (triple clamp?) for version s n maybe a showa shocks or ss headers...will give the above-mentioned scrpyards a try though..

anyone willing to share their experience with scrapyards?

Sorry for double post....

Nowadays... scrap yard are slowly dying out due to the inflow of cheap oem parts fr China...
Scrapyard part are usually used... abused or nt depend on your luck...
pricing wise some mayb cheaper than those MIC parts soem may not...
what parts u nid??
Let me noe i may have the lobang....
Call or sms or pm me mate 96284016

[returner]

Dear all S4 bros,

Please advice where to install spec 3 whole set tail board on my versionR, please advice location, time spend, prices....
just got one set import from china at $180...

[stwb1981]

Dear all S4 bros,

Please advice where to install spec 3 whole set tail board on my versionR, please advice location, time spend, prices....
just got one set import from china at $180...

Should get all fr Msia... cheap cheap...lol

[amatbeck]

Hi, anyone knows where to get cheap fairing for my spec 1? or anwhere to get 2nd hand fairing?

[Pericoon]

Hi, anyone know where to repair the rpm meter of my Version S? Or anyone got a spare front fender(mudguard) in maroon color for sale?

[ducktale83]

Hi, anyone know where to repair the rpm meter of my Version S? Or anyone got a spare front fender(mudguard) in maroon color for sale?

I juz bought front fender frm ahboy but only got black colour:-)

Sent from my IPHONE6 using Tapatalk 2

[GhostBiker]

During the mid 2000s, we see many Super4s with Rxz head cowlings, now we don't see them often. Wonder if its outdated to install it back on a Version S now??? And of course, instead of the new 'Spec3' tailboards, we had the integrated taillight with signals. Truly classic masterpieces. LOL

[Pericoon]

I juz bought front fender frm ahboy but only got black colour:-)

Sent from my IPHONE6 using Tapatalk 2

Can share the price or pm me the price?

[Pericoon]

Any recommendation for new handlebar? My was bent when bought the bike. Which type available for Version S and pros n cons of aftermarket handlebar? Can pass inspection?

[stwb1981]

During the mid 2000s, we see many Super4s with Rxz head cowlings, now we don't see them often. Wonder if its outdated to install it back on a Version S now??? And of course, instead of the new 'Spec3' tailboards, we had the integrated taillight with signals. Truly classic masterpieces. LOL

Haha... yup still have nw lah but i personally feel it pretty ugly haha...
some more the headlight so small...
nowadays there are so many head cowl available juz clip on ok liao....
Any way personally again, the spec 3 tail oso nt nice pref the old skool looks of a S4...

Any recommendation for new handlebar? My was bent when bought the bike. Which type available for Version S and pros n cons of aftermarket handlebar? Can pass inspection?

Inspection sure pass as long u gt handlebar mate...lol
no worries...

[GhostBiker]

anyone 'obsessed' with the stock exhaust performance and sound? LOL...
Harley riders claim loud pipes saves lives, does anyone really appreciate the buzzing and whining of an inline-4? What do i get for spending more than $500 on a yoshi or leovince?

[Pericoon]

Haha... yup still have nw lah but i personally feel it pretty ugly haha...
some more the headlight so small...
nowadays there are so many head cowl available juz clip on ok liao....
Any way personally again, the spec 3 tail oso nt nice pref the old skool looks of a S4...


Inspection sure pass as long u gt handlebar mate...lol
no worries...

Thanks. So far during my research only found three types, Renthal and Driven and one call Fat bar.. Hope I get it right. Anyone using or can recommend. In term of comfort, which is the best?

[Ariess]

hi guys jus to check ,
if i were to install a box and rack on my version S , isit specified which rack or across the board for all S4?

i seen a few ads in garage sales but wondering which is actually compatible.
thanks

[Pericoon]

Thanks. So far during my research only found three types, Renthal and Driven and one call Fat bar.. Hope I get it right. Anyone using or can recommend. In term of comfort, which is the best?

Or anyone selling their original handlebar?

[ahdon]

Hi guys, recently i noticed that when i start the bike, it does not start on the first crank. It usually starts after i hear a sound of air pushing through the exhaust before it starts. Sounds like fth bike is farting. Any ideas? And i also noticed that the bike takes longer to start at the end of the day when i had ridden it on high rev in the morning. Any one with similar experience or know what's wrong?

[stwb1981]

Ooooo.... could b the head gasket leaking??
check wif the pros here for more advice...

[Ah Pek]

Hi guys, recently i noticed that when i start the bike, it does not start on the first crank. It usually starts after i hear a sound of air pushing through the exhaust before it starts. Sounds like fth bike is farting. Any ideas? And i also noticed that the bike takes longer to start at the end of the day when i had ridden it on high rev in the morning. Any one with similar experience or know what's wrong?

When was ur spark plugs last changed?

[ur13an]

Hi bros, just got my ver s 50th anniversary bike last week.. when parked on side stand, my bike slants so much that makes me "eat" into the lot beside or barely touching the box/side mirrors of the bike parked beside mine.. any solutions to this? Was qouted $85 for a new side stand which i think might nt necessarily solve this problem?

[Ah Pek]

Hi bros, just got my ver s 50th anniversary bike last week.. when parked on side stand, my bike slants so much that makes me "eat" into the lot beside or barely touching the box/side mirrors of the bike parked beside mine.. any solutions to this? Was qouted $85 for a new side stand which i think might nt necessarily solve this problem?

An original new stand would definitely help. Your current one bend too much liao. Another alternative is to take it off and bend back (clamp on with a vice and use a larger circumference water pipe..slot in and counter bend it)..make sure the base end of your stand still has a flat base plate..not sure what I'm saying..look at neighbouring S4 stands.

[fluzzy]

What can i do so that my brake feels more smooth while braking? for both front and rear brake?

My speedo isnt working and my RPM is fine. What can i do to verify the actual fault? and the cost to change/replace of sensor/speedo?

[blazeman]

do you guy encounter this problem ?during riding when wan to release and twist back throttle feel very tight.

[ur13an]

An original new stand would definitely help. Your current one bend too much liao. Another alternative is to take it off and bend back (clamp on with a vice and use a larger circumference water pipe..slot in and counter bend it)..make sure the base end of your stand still has a flat base plate..not sure what I'm saying..look at neighbouring S4 stands.

I see.. thanks!

[Ah Pek]

What can i do so that my brake feels more smooth while braking? for both front and rear brake?

My speedo isnt working and my RPM is fine. What can i do to verify the actual fault? and the cost to change/replace of sensor/speedo?

Perhaps u wanna tell us what version is ur S4? As for the first question...can u be more specific..what u meant by not smooth?

[Ah Pek]

do you guy encounter this problem ?during riding when wan to release and twist back throttle feel very tight.

If u have balancer at the end of ur handle bar..ur rubber grip may be touching against it..rectiied this by cutting a bit more of the rubber grip end off or loosen ur balancer locking screw/allen ket a bit looser. The first option is preferred. If this is not the case..check your throttle cable and see if it's loose as in no "torsion" or the way its run under the tank is wrong.

[Hound04]

Does anyone know how or where to install a new belly pan for PB1?