[Discussion] Super Four General Enquiry Thread

[syeDsTp]

What u mean by knock? I still need to push then can start.

Sent from my GT-N7000 using Tapatalk

[}STRYKER{]

What u mean by knock? I still need to push then can start.

Sent from my GT-N7000 using Tapatalk

Knock as in u take a screw driver or spannar n give the starter carbon a few knocks to free it from jamming. But knocking is only a temporary solution...best to get it changed lah.


}STRYKER{ sent this post via iPhone using Tapatalk

[syeDsTp]

The starter carbon gt a cable attached to it right?

Sent from my GT-N7000 using Tapatalk

[}STRYKER{]

The starter carbon gt a cable attached to it right?

Sent from my GT-N7000 using Tapatalk

Yup left side of the bike just above ur coils...


}STRYKER{ sent this post via iPhone using Tapatalk

[repek666]

hi . can i ask which bike shop do valve clearance on the spot? and how much

Sent from my GT-I9100 using Tapatalk 2

[}STRYKER{]

hi . can i ask which bike shop do valve clearance on the spot? and how much

Sent from my GT-I9100 using Tapatalk 2

Doubt they can complete it in one day.
What i did was first to change my timing chain,tensioner & camcover o ring in one day.
Den i went over another day to get them to balance my shims in abt 6 hrs.
But i did not changed engine oil or coolant when i did both servicing...


}STRYKER{ sent this post via iPhone using Tapatalk

[repek666]

okae which shop?? planet??? n hw much???

Sent from my GT-I9100 using Tapatalk 2

[repek666]

okae which shop?? planet??? n hw much???

Sent from my GT-I9100 using Tapatalk 2

[}STRYKER{]

okae which shop?? planet??? n hw much???

Sent from my GT-I9100 using Tapatalk 2

I did my cbr1100xx at global.
Timing chain,tensioner & camcover o ring is $250.
Balancing of the shims is $120.
But its best to make an appt with them so tat they will be prepared...


}STRYKER{ sent this post via iPhone using Tapatalk

[kok_07]

Hi, I just bought a spec 1. When moving off den got some problem. bike power like stuck stuck den awhile ok. Idling at 1.5 after awhile it decrease den engine die off. Wat is the problem that u all knw? Mechanic told me is carb problem. Dirty and need tunning? Is it true?

[repek666]

yep2 it carb.. dirty n many things inside shd be wear n tear n nid to change.. done at unique... cost me $200..

Sent from my GT-I9100 using Tapatalk 2

[holdurhead]

Hi when my vtec open got black smoke, friend day exhaust got too much carbon. How to remove them?

[stwb1981]

Hi, I just bought a spec 1. When moving off den got some problem. bike power like stuck stuck den awhile ok. Idling at 1.5 after awhile it decrease den engine die off. Wat is the problem that u all knw? Mechanic told me is carb problem. Dirty and need tunning? Is it true?

Refer to the non vtec thread.... my experience wif my bike is there...

Hi when my vtec open got black smoke, friend day exhaust got too much carbon. How to remove them?

simple juz ride harder...!!!
do note it doesn't mean U gt to travel @ high speed or clear meter...
Rather U can high rev from gear 1 onwards...
Carbon oso clear...
Safest go NSHW & clear... Singapore own risk...
BUT DO SO AT YR COMFY PACE...

[Nick87]

Hi all any JB shop to intro can do vtec 3 well

[stwb1981]

Hi all any JB shop to intro can do vtec 3 well

Do what things mate??

I going in later to ah qua lane there to my regular shop then...

If basic change eo, plug etc shouldn't b a prob...
if top overhaul or more complex stuff...
My $$$ is in Sg...

Cheers!!!

[ahso0n]

Any fellow rider know the price of second hand LV SBK endcan?

[Nick87]

Plug can change in jb which shop

[stwb1981]

Plug can change in jb which shop

Pricing wise.... I rather change in sg... not worth....
WK motorsport have....
think most shop have lah....
try the ones @ ah qua lane... (sadly that the only place i noe..lol)

[Arlwynn]

Hi guys just to inform that i have these few Revo items for sale ...

1- Original Bagster Tankbra for Revo, Silver Wing Tribal Edition. ( Used )( Good Condition ) ( $120 )
2- Gi-Pro DS Series Gear Indicator For Revo "PNP" NO Wire Cutting or Spicing of Wire.
( Used )( Red Colour Indicator ) ( $150 )
3- "NEW" Front Fork Axle Slider ( $55 )
4- "NEW" VoltMeter ( $35 )
5- "NEW" NGK IridiumIX Spark Plugs "CR8EHIX-9" X 4 NO.S ( $48 )

All items in Good and Working Condition : 9/10
Any further Information can PM me ...

[jimmmmmy]

Hi, anyone of you knw the trade in price for spec 1 nowadays?

[stwb1981]

I notice tat many riders are paying much higher for a simple yet very useful device...
I trying to maintain @ $18 ALL YEAR ROUND to help ease all riders' $$$ lol

As said...
FOR CB400 (ALL YEARS) AKA S4 RIDERS

MB DIGITAL VOLTMETER aka MB VOLTY
AVAILABLE IN RED OR BLUE
SPECIAL TO ALL @ $17 CASH & CARRY
ALL YEAR ROUND OR TILL I CHANGE BIKE AGAIN...

CONTACT: STEVEN 96284016

I used to be the 1st in singapore to bring in green but demand has been rather slow....
If anyone is keen on green, kindly consoldiate the orders before approaching me
Looking at 8 pcs or more if possible but subject to demand & to my discretion.
Seek all understanding on this...

Go to non vtec thread to read or find out why this promo came about...

Cheers!!!

[Juggy]

hi everyone

Just got a super 4 spec 1. and i notice that my idling rpm fluctuates slightly when idle. means you can see the needle moving and engine sound does not settle to a constant speed idle is it normal?? is something rong with the bike?

BTW if any one want to change their stock seat with mine do drop me a PM willing to top up. looking for a stock spec1/2 seat. Ie never cut before. feel that my pillion seat is slightly lower.. dont like as i like ppl to hug me when i ride

[devil.L]

Send your bike for a carb wash, back at your shop they shd do it for free, since its newly from em.
After the wash, thy shd tune / set it to be just fine.

hi everyone

Just got a super 4 spec 1. and i notice that my idling rpm fluctuates slightly when idle. means you can see the needle moving and engine sound does not settle to a constant speed idle is it normal?? is something rong with the bike?

BTW if any one want to change their stock seat with mine do drop me a PM willing to top up. looking for a stock spec1/2 seat. Ie never cut before. feel that my pillion seat is slightly lower.. dont like as i like ppl to hug me when i ride

[Juggy]

Send your bike for a carb wash, back at your shop they shd do it for free, since its newly from em.
After the wash, thy shd tune / set it to be just fine.

Thanks, but i just did a Carb servicing when i got the bike that means they did not tune it properly.....

[vinz74]

S4 bros, recently when riding there a unknown rubbing sound coming from the front wheel or somewhere infront, had change to new brake pads but sound still exist... Anyone can advice??

[Ah Pek]

S4 bros, recently when riding there a unknown rubbing sound coming from the front wheel or somewhere infront, had change to new brake pads but sound still exist... Anyone can advice??

Could be ur brake hose or clutch cable rubbung the fender or the hose metal guide. Spary some oil or WD40 on the contact part of these and see how.

[vinz74]

Could be ur brake hose or clutch cable rubbung the fender or the hose metal guide. Spary some oil or WD40 on the contact part of these and see how.

Thks bro!! Will take a look ..

[^Ah Jeff^]

Guys I'm kinda of curious. How many km then u guys goes for servicing & which workshop u goes? Just want to know more..

[Mutaga]

hi all, i just brought a spec 1 about 2 weeks ago. all was fine. but the last time, i went jb to pump 95. then problem came. yesterday, i was about to park my bike. the rpm just slowly went down from 1.5k to 1k then die off by itself. happened this morning as well. took me about 7 to 8 times to start the bike again. anyone can let me know what is the problem? cheers.

[Jehuty]

Anyone knows any website where I can purchase S4 stuffs from overseas?

[starr]

Anyone knows any website where I can purchase S4 stuffs from overseas?

What stuffs u looking for?

[Jehuty]

What stuffs u looking for?

Anything la, from accessories to full exhaust systems. There's one, Japan Webike but its more on the expensive side.

[andrew0511454]

hi.. im riding a super4 spec3 .. and there is some problem with my bike.. when the bike is on the move.. about 100km/hr.. i realised my speedometer needle swipe to zero and stay there for a minute... there is also a lost of power and when i try to throttle it does not increase its speed.

i have no problem starting the bike.. so i m wondering is it the rectifier that is going to spoilt?? advice? thanks ~

[krp]

hi.. im riding a super4 spec3 .. and there is some problem with my bike.. when the bike is on the move.. about 100km/hr.. i realised my speedometer needle swipe to zero and stay there for a minute... there is also a lost of power and when i try to throttle it does not increase its speed.

i have no problem starting the bike.. so i m wondering is it the rectifier that is going to spoilt?? advice? thanks ~

May be your battery problem

[Salak]

hello there..
I bought a 2nd hand spec3 and Im experiencing something like a vibrating sound "trrrrrr" coming from the engine area when I open my throttle to activate the VTec at RPM 7-8.
I can feel power comes in and the sound of the exhaust became louder.
Especially when I dragged my 4th gear to pick up to 5th gear.. I can hear the "trrrrrr"....
Is the VTec valve faulty?

Hope to hear ur comments!

[fabianau]

is aftermarket balancers like rizoma, motivation useful for super4?

[dlzhdan]

hi, anyone has any idea how to adjust the time on a vtec 2 meter? ive change multiple ways of pressing both buttons on the meter to no avail. could someone please assist? thankss!

[aminnurasyid]

Hi bros,
do checkout the new JackUp.
Works with ALL motorbikes with spools and almost horizontal double swingarm.
PM for more details or you guys can view the FB yah.

http://www.facebook.com/JackUpBike/info

[nazrulz]

hi bros,

i just got a spec 3. I realise that at high speed, my bike vibration quite hard to the extend when i press my front brake, the brake lever is vibrating. also, wen i press the front brake if i brake late, it produce a sound similar to a bicycle brakes that are worn out.last thing, wen i free hand, the bike move sideways to the right. are these normal? btw which shop in the east should i go to change engine oil and spark plug plus wash carburator? sorry for the long post.. noob here..

[LXY]

hi bros,

i just got a spec 3. I realise that at high speed, my bike vibration quite hard to the extend when i press my front brake, the brake lever is vibrating. also, wen i press the front brake if i brake late, it produce a sound similar to a bicycle brakes that are worn out.last thing, wen i free hand, the bike move sideways to the right. are these normal? btw which shop in the east should i go to change engine oil and spark plug plus wash carburator? sorry for the long post.. noob here..

vibration issue = steering cone
brake issue = disc/ pad

[manbai]

vibration issue = steering cone
brake issue = disc/ pad

Could be the front wheel bearing too.

[Jehuty]

I hear a scraping noise when I free wheel, I can't put my finger on where it comes from, its not the brake pads nor the chain. Any ideas? And where to do good grounding?

[evoVII]

Hi all. Just have some enquires to make with the more senior people here. Is it normal for the fan to on after lets say about 10 minutes or so in moderate traffic on normal roads not on highway. And also i dont know if its a problem or not but after turning the ignition on, the light for the radiator does not light up where as everything else does. Would that be considered so called a sign to any problems related to the radiator. Currently riding a spec 3 and i got the bike about a month ago and so i'm quite unsure about some stuff. Would appreciate any advice given. Thanks in advance!

[Ah Pek]

I hear a scraping noise when I free wheel, I can't put my finger on where it comes from, its not the brake pads nor the chain. Any ideas? And where to do good grounding?

Have u check ur brake pads?..could be the pad reaching its wera and tear point which normally has a 'marker' that tuches ur brake disc as a warning that it's worn.

[Ah Pek]

Hi all. Just have some enquires to make with the more senior people here. Is it normal for the fan to on after lets say about 10 minutes or so in moderate traffic on normal roads not on highway. And also i dont know if its a problem or not but after turning the ignition on, the light for the radiator does not light up where as everything else does. Would that be considered so called a sign to any problems related to the radiator. Currently riding a spec 3 and i got the bike about a month ago and so i'm quite unsure about some stuff. Would appreciate any advice given. Thanks in advance!

Looks more like a tell tale sign that trouble is coming as the fan shouldn't be coming on that often or sooner as per ur description. As for the temp light indicator..not sure about Spec 3 but for non Vetec bikes..its not on for self check like the oil temp light indicator. At any rate..the worst I can think of is that the buld or led for it may have multfunction.

[aminnurasyid]

Here's a link to JackUp video. JackUp able to support by spool/rearaxle and under swingarm for certain bikes.

http://m.youtube.com/index?desktop_u...?v=RjJ6g_SBqyo


Sent from my iTouch using Tapatalk

[Nikki]

Hi... Has anyone installed a givi windshield on revo?
Bought a750 from shop as was told this fits revo but after I went home, realized it doesn't quite fit headlights bcos of the headlight bar supporting speedo and tacho.
Would anyone know if I need to mod or change the headlight so that it can fit?

[b1tch_boy]

Hi. I'm new to super 4. I'm riding a spec 3. There is a sound difference when i clutch in and out. Is it normal? Plus, while i was riding around for about 20-30 min, my fan suddenly turned on. Is this common?

[b1tch_boy]

i experience the same problem as you bro

[kelena]

Hi,

My bike is a 2nd hand one, and the first owner dropped it on it's left. So what happens now is that when the wheels are aligned (i got a friend to stand well ahead and with me sitting on the bike) the handle bars are slightly off to the right.

I find it rather hard to steer (it keeps moving to the right) when I'm moving off, but at normal speeds, there are no steering issues, and the bike tracking straight.

It's just that when I look at the speedo, I can see the misalignment of the handle bars on my peripheral vision and it's quite irritating.

Hence, is there any way of setting the bike handle bars in alignment correctly, without costing a bomb?

Thanks all!