User Tag List

Page 1 of 2 12 LastLast
Results 1 to 50 of 64

Thread: Dimension & Specification for Number Plates from LTA

  1. #1
    BluEGaZeR
    has no status.
    Kruzers BluEGaZeR's Avatar
    Join Date
    Aug 2002
    Location
    Planet New Eden
    Posts
    1,999
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default



    Our Ref: XXXXXXXXXXXXXXXXXXXXXX
    Date: XX-XX-XXXX
    Tel: 1800 CALL LTA (2255 582)
    Fax: 6553 5329

    Dear Mr XX,

    RE: NUMBER PLATE QUERIES
    FEEDBACK NUMBER: XXXXX

    We refer to your feedback dated XX-XXX-XXXX.

    2 We would like to inform you that the vehicle number plate shall be placed not more than 1 metre from the ground in a vertical position. The number plate normally has white, silver or light grey letters and figures on a black background. However, if the number plate is made of reflex reflecting material, the front number plate will consist of black letters and figures on a white background; and the rear number plate will consist of black letters and figures on a yellow background.

    3 For the front number plate, it shall meet the following requirements:

    (a) the letters and figures are 70 mm high, 50 mm wide and 10 mm broad;
    (B) the space between adjoining letters and between adjoining figures shall be 10 mm;
    © the space between the letters and figures shall be 20 mm;
    (d) a margin between the nearest part of any letter or figure and the top or bottom of the number plate shall be 10 mm;
    (e) a margin between the nearest part of any letter or figure and the sides of the number plate shall be 20 mm.

    In the case of the front number plate of motorcycle, the above dimensions may be reduced by half.

    4 For the rear number plate of motorcycle, it shall meet the following requirements:

    (a) the letters and figures are 50 mm high, 30 mm wide and 5 mm broad;
    (B) the space between adjoining letters and between adjoining figures shall be 10 mm;
    © the space between the letters and figures shall be 20 mm;
    (d) a margin between the nearest part of any letter or figure and the top, bottom and sides of the number plate shall be 10 mm.

    5 We have no objection for you to add your name at the bottom of the number plate provided that it is not within the margin of the number plate. You are to ensure that no other figures or letters and no design advertisement or ornamentation shall be placed near the identification mark in such a manner as to be liable to render it more difficult to read or distinguish the identification mark of the vehicle when in motion.


    Yours sincerely



    (SIGNED IN LOTUS NOTES)
    XXXXXXX
    SENIOR TECHNICAL OFFICER
    VEHICLE ENGINEERING
    VEHICLE SERVICES

  2. #2
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Our Ref: LTA/CSV/F20.032.000/3384/1
    Date: 12-JUL-2004
    Tel: 1800-2255 582 (1800-CALL LTA)
    Fax: 6553 5329

    Dear Mr XXX,

    NUMBER PLATE REGULATIONS & MATERIAL USED
    FEEDBACK NUMBER: 153370

    Thank you for your enquiries of 30-JUN-2004.

    2. We wish to inform you that the technical requirements for motorcycle licence plates used in Singapore can be found in Rule 15 and Fourth Schedule of the Road Traffic (Motor Vehicles, Registration and Licensing) Rules.

    3. In summary, these rules specify that licence plates should comply with either of the following descriptions (colour code):

    a) Letters and figures are white, silver or light grey on a non-reflective black background for both front and rear; or
    b) Letter and figures are black on a white reflex-reflecting background for the front, and on a yellow reflex-reflecting background for the rear.

    4. The front licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 35 mm high, 25 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 5 mm;
    © The space between the letters and figures shall be 10 mm;
    (d) A margin between the nearest part of any letter or figure and the top
    or bottom of the number plate shall be 5 mm;
    (e) A margin between the nearest part of any letter or figure and the sides of the licence plate shall be 10 mm.

    5. The rear licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 50 mm high, 30 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 10 mm;
    © The space between the letters and figures shall be 20 mm;
    (d) A margin between the nearest part of any letter or figure and the top, bottom and sides of the licence plate shall be 10 mm.
    (e) For licence plate that consists of 2 rows of figures and letters, the space the 2 rows shall be 10 mm.

    6. No other figures or letters, design advertisement or ornamentation shall be placed near the licence plate in such a manner as to render it more difficult to read or distinguish the registration number of the motorcycle when in motion.

    7. Many licence plates used in Singapore are attached to plastic licence plates holders that contain wording and brand names. We have no objection to the fixing of licence plates with such holders if it meet the above requirements. In addition, the wordings on such holders shall not contain obscenities or profanities and shall not be derogatory seditious.

    8. As for your enquiry on the sticker type licence plate for the front, we have no objection to it so long as the above requirements are met. We hope we have addressed your enquiries satisfactorily, thank you.


    Yours sincerely,



    (SIGNED IN LOTUS NOTES)
    GOH SEONG HONG
    for MANAGER
    VEHICLE ENGINEERING DEPARTMENT
    VEHICLE & TRANSIT LICENSING DIVISION
    LAND TRANSPORT AUTHORITY

     

     
  3. #3
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Please note that point number 8 I asked in reference to the piaggio x9 but my main excuse was that the front was uneven

  4. #4
    deganduss
    deganduss
    has no status.
    Edit
    Guest

    Default

    Originally posted by Fass@Jul 13 2004, 12:40 AM
    Please note that point number 8 I asked in reference to the piaggio x9 but my main excuse was that the front was uneven
    So sticker at front fender is not wrong lah

  5. #5
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by deganduss@Jul 13 2004, 11:08 PM
    So sticker at front fender is not wrong lah
    Just got off the phone with one of the chaps at LTA. Font and size of the sticker plate must be as stated. Only metal plate is allowed for fender, sticker is approved for usage around the windshield position only

  6. #6
    honda475
    has no status.
    Class 2B honda475's Avatar
    Join Date
    Jan 2004
    Location
    sgp
    Posts
    228
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Fass@Jul 19 2004, 10:22 AM
    Just got off the phone with one of the chaps at LTA. Font and size of the sticker plate must be as stated. Only metal plate is allowed for fender, sticker is approved for usage around the windshield position only
    but whether metal plate or sticker type is not stated in the requirment.

    is somebody slapping their own face????

    "we don't object the use of sticker type as long as it meets all the requirments above"

    i am really confused /////..........
    once a honda
    still a honda
    honda again!
    always a honda
    Honda..........a...a.a..a
    <u>ALWAYS THE FIRST CHOICE</u>

  7. #7
    w1n9
    is kwackin'
    TeePee w1n9's Avatar
    Join Date
    Oct 2003
    Posts
    4,069
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    2 Thread(s)

    Default

    Originally posted by 6niner@Jul 20 2004, 12:29 AM
    but whether metal plate or sticker type is not stated in the requirment.

    is somebody slapping their own face????

    "we don&#39;t object the use of sticker type as long as it meets all the requirments above"

    i am really confused /////..........
    i bet there are more regulations in the lta book that the tps and rovs are even more confused&#33;
    Pre-launch Product
    http://queue.social/2ko401X

  8. #8
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    thank you fass for the call&#33;
    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  9. #9
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Exhaus&#045;tion@Jul 20 2004, 04:49 AM
    thank you fass for the call&#33;
    Oh I didn&#39;t call them, they called me wahahaha
    Might be paying them a visit this sat for further number plate discussion

  10. #10
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Fass@Jul 20 2004, 07:45 AM
    Oh I didn&#39;t call them, they called me wahahaha
    Might be paying them a visit this sat for further number plate discussion
    ...den discuss approval on full system exhaust....
    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  11. #11
    rvf7972
    rvf7972
    has no status.
    Edit
    Guest

    Default

    Originally posted by Exhaus&#045;tion@Jul 20 2004, 04:00 PM
    ...den discuss approval on full system exhaust....


    muzzy&#39;s

     

     
  12. #12
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by rvf7972@Jul 20 2004, 06:43 PM


    muzzy&#39;s
    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  13. #13
    WildCard
    has no status. Not that he cares....
    SBF Senior Moderator WildCard's Avatar
    Join Date
    Dec 2002
    Location
    West Side, bro!
    Posts
    7,925
    Feedback Score
    1 (100%)
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default

    M4 full systems?...

    okie, tats asking too much....

  14. #14
    rvf7972
    rvf7972
    has no status.
    Edit
    Guest

    Default

    Originally posted by WildCard@Jul 20 2004, 08:02 PM
    M4 full systems?...

    okie, tats asking too much....
    hw abt yoshi rs3 tri oval? 4 u r tl


  15. #15
    2_wheeler
    has no status.
    SBF Scooters 2_wheeler's Avatar
    Join Date
    Dec 2002
    Location
    N 1.298595 , E 103.852557
    Posts
    2,476
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Fass@Jul 20 2004, 07:45 AM
    Oh I didn&#39;t call them, they called me wahahaha
    Might be paying them a visit this sat for further number plate discussion
    you may wanna check with them regarding displaying of Road Tax also..

    or you would like to gather a list of question to ask them.
    Rare Honda Silverwing 600 for Sale!

    http://www.singaporebikes.com/forums/showthread.php/477349-Rare-Honda-Silverwing-600

  16. #16
    roger
    has no status.
    SBF Lacer roger's Avatar
    Join Date
    Apr 2003
    Location
    Eastern Jupiter
    Posts
    7,231
    Feedback Score
    0
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by 6niner@Jul 20 2004, 12:29 AM
    but whether metal plate or sticker type is not stated in the requirment.

    is somebody slapping their own face????

    "we don&#39;t object the use of sticker type as long as it meets all the requirments above"

    i am really confused /////..........
    ermmm paste sticker on fender?? For who to see sia?

    IBA member #25267

  17. #17
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by 2_wheeler@Jul 20 2004, 09:48 PM
    you may wanna check with them regarding displaying of Road Tax also..

    or you would like to gather a list of question to ask them.
    APPROVE...

    1) more aftermarket exhaust, end can or lagi best...fullsystem&#33;
    2) custom colour speedo display
    3) tinted headlite protector during daytime
    4) increase speed limit on highways during-off peak wee hours
    5)
    6)
    7)
    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  18. #18
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  19. #19
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Exhaus&#045;tion@Jul 20 2004, 04:00 PM
    ...den discuss approval on full system exhaust....
    Hahahaa sorry not familiar with the topic, I know they do approve changing of the exhaust provided you send your vehicle for inspection together with a test report (from the manufacturer) of the exhaust which was tested with the same model as your bike

  20. #20
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by 2_wheeler@Jul 20 2004, 09:48 PM
    you may wanna check with them regarding displaying of Road Tax also..

    or you would like to gather a list of question to ask them.
    What about the displaying of road tax? Care to be more specific? This I can ask

  21. #21
    Fass
    has no status.
    TeePee Fass's Avatar
    Join Date
    Oct 2003
    Posts
    3,727
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by roger@Jul 21 2004, 12:42 AM
    ermmm paste sticker on fender?? For who to see sia?
    who_noes hah..... who_noes

     

     
  22. #22
    Exhaus-tion
    has no status.
    TeePee Exhaus-tion's Avatar
    Join Date
    Apr 2004
    Location
    WeReVa i MaY RoAm
    Posts
    2,402
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Fass@Jul 21 2004, 10:18 AM
    who_noes hah..... who_noes
    I DON&#39;T KNOW THE KEY TO SUCCESS, BUT THE KEY TO FAILURE IS TRYING TO PLEASE EVERYBODY




    <u>BUY MATTRESS FREE HANDPHONE</u>

  23. #23
    biking nomad
    has no status.
    Class 2 biking nomad's Avatar
    Join Date
    Jan 2004
    Location
    On The Road
    Posts
    1,318
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I think he wants to know if its absolutely necessary to display valid road tax disc on the motorcycle.

    Can it be kept on the rider or in a compartment in the bike? Or must it be dispalyed on the bike?

    Let us know if u have news on this...tks mate&#33;
    Someday, home will be where my front wheel points.


    Astride a 2002 Yamaha Fazer FZS600

  24. #24
    Cyanide14
    has no status.
    SBF Lacer Cyanide14's Avatar
    Join Date
    Nov 2002
    Location
    9V-SKA
    Posts
    9,435
    Feedback Score
    0
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Exhaus&#045;tion@Jul 21 2004, 10:10 AM
    APPROVE...

    2) custom colour speedo display
    huh?
    this one they also catch?
    why?
    My Dream Car, see who wants to cut my lane and tail-gate me......

  25. #25
    guezz007
    has no status.
    Class 2B guezz007's Avatar
    Join Date
    Nov 2003
    Posts
    439
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by Fass@Jul 13 2004, 12:53 AM
    Our Ref: LTA/CSV/F20.032.000/3384/1
    Date: 12-JUL-2004
    Tel: 1800-2255 582 (1800-CALL LTA)
    Fax: 6553 5329

    Dear Mr XXX,

    NUMBER PLATE REGULATIONS & MATERIAL USED
    FEEDBACK NUMBER: 153370

    Thank you for your enquiries of 30-JUN-2004.

    2. We wish to inform you that the technical requirements for motorcycle licence plates used in Singapore can be found in Rule 15 and Fourth Schedule of the Road Traffic (Motor Vehicles, Registration and Licensing) Rules.

    3. In summary, these rules specify that licence plates should comply with either of the following descriptions (colour code):

    a) Letters and figures are white, silver or light grey on a non-reflective black background for both front and rear; or
    b) Letter and figures are black on a white reflex-reflecting background for the front, and on a yellow reflex-reflecting background for the rear.

    4. The front licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 35 mm high, 25 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 5 mm;
    © The space between the letters and figures shall be 10 mm;
    (d) A margin between the nearest part of any letter or figure and the top
    or bottom of the number plate shall be 5 mm;
    (e) A margin between the nearest part of any letter or figure and the sides of the licence plate shall be 10 mm.

    5. The rear licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 50 mm high, 30 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 10 mm;
    © The space between the letters and figures shall be 20 mm;
    (d) A margin between the nearest part of any letter or figure and the top, bottom and sides of the licence plate shall be 10 mm.
    (e) For licence plate that consists of 2 rows of figures and letters, the space the 2 rows shall be 10 mm.

    6. No other figures or letters, design advertisement or ornamentation shall be placed near the licence plate in such a manner as to render it more difficult to read or distinguish the registration number of the motorcycle when in motion.

    7. Many licence plates used in Singapore are attached to plastic licence plates holders that contain wording and brand names. We have no objection to the fixing of licence plates with such holders if it meet the above requirements. In addition, the wordings on such holders shall not contain obscenities or profanities and shall not be derogatory seditious.

    8. As for your enquiry on the sticker type licence plate for the front, we have no objection to it so long as the above requirements are met. We hope we have addressed your enquiries satisfactorily, thank you.


    Yours sincerely,



    (SIGNED IN LOTUS NOTES)
    GOH SEONG HONG
    for MANAGER
    VEHICLE ENGINEERING DEPARTMENT
    VEHICLE & TRANSIT LICENSING DIVISION
    LAND TRANSPORT AUTHORITY
    The front licence plates for motorcycle rite? Those bike with fairings for example Yamaha R1 have their plates pasted on the windshield. I believe many race bikes also have their number plates on the wind shield.

    How abt on SUPER 4? If i installed a windshield can i also paste the number plate on it?

    Cheers&#33;
    Cheers!
    Jacky

    Past: TA150
    Present: XL1200C

  26. #26
    kinwei
    says Buang bike ride faster!
    TeePee kinwei's Avatar
    Join Date
    Aug 2003
    Location
    East Side
    Posts
    3,969
    Feedback Score
    0
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by w1n9@Jul 20 2004, 02:37 AM
    i bet there are more regulations in the lta book that the tps and rovs are even more confused&#33;
    I think better to get an original copy from LTA stating that sticker type of number plate is allowed on the windshield. Then keep that letter with you whenever you ride the bike. If any ROV want to find trouble with you, at least you got something black and white to show them in their face.

  27. #27
    guezz007
    has no status.
    Class 2B guezz007's Avatar
    Join Date
    Nov 2003
    Posts
    439
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by kinwei@Aug 14 2004, 03:00 PM
    I think better to get an original copy from LTA stating that sticker type of number plate is allowed on the windshield. Then keep that letter with you whenever you ride the bike. If any ROV want to find trouble with you, at least you got something black and white to show them in their face.
    Huh? You mean it&#39;s possible? But still have to get from LTA huh... ?
    Cheers!
    Jacky

    Past: TA150
    Present: XL1200C

  28. #28
    kinwei
    says Buang bike ride faster!
    TeePee kinwei's Avatar
    Join Date
    Aug 2003
    Location
    East Side
    Posts
    3,969
    Feedback Score
    0
    Mentioned
    6 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by guezz007@Aug 14 2004, 03:39 PM
    Huh? You mean it&#39;s possible? But still have to get from LTA huh... ?
    Well this I not sure.... But it better than wait kanna stop by ROV and waste your saliva with them and yet they still heck care you.

  29. #29
    -=[PeNsKe]=-
    has no status.
    TeePee -=[PeNsKe]=-'s Avatar
    Join Date
    Jun 2004
    Posts
    4,583
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by rvf7972@Jul 20 2004, 08:20 PM
    hw abt yoshi rs3 tri oval? 4 u r tl

    Dun think there&#39;s a RS 3 tri-oval. I am using a RS 3 carbon fibre Duplex full system. But as for the tri-oval, it&#39;s called a TRD.

  30. #30
    R1szuan
    R1szuan
    has no status.
    Edit
    Guest

    Default

    <span style='color:yellow'> i was informed there is no longer a need to display a road tax disc on your bike, As this was quoted by 2 tp officer who stop me along CTE.

    Err if you need black and white...actually there is no black and white as most officers have been informed.

    just a small quote.
    </span>

  31. #31
    yappiez
    has no status.
    Class 2
    Join Date
    Feb 2004
    Posts
    1,258
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    brother Risz,
    Yellow text very hard to read...

     

     
  32. #32
    darksoul81
    has no status.
    Class 2B
    Join Date
    Mar 2006
    Location
    woodlands
    Posts
    242
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    juz highlite over the yellow text


    RXK
    Zing
    KDX
    Skipper
    Runner VXR
    DR-Z400S/SM

  33. #33
    yanuk
    has no status.
    Class 2B yanuk's Avatar
    Join Date
    Jan 2006
    Posts
    259
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Originally posted by darksoul81@Jul 14 2006, 04:03 PM
    juz highlite over the yellow text
    you dug up a 2 year old thread..
    Big brother's watching...

    To do list:
    - Steel brake hoses (In progress...)
    - Rewire bike
    - Repaint fairing and clean up bike
    - Replace exhaust system (DONE!)


    Always in my heart...

  34. #34
    tidy
    has no status.in your face.
    P Plate
    Join Date
    May 2005
    Posts
    178
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    is the fine for a bended number plate $120?

  35. #35
    kurarensu
    is cute ^^
    SBF CB400s kurarensu's Avatar
    Join Date
    Jul 2006
    Location
    Planet Earth
    Posts
    9,140
    Feedback Score
    2 (100%)
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)

    Default

    $70 for any number plate fine

    Lousy Noob Rider

  36. #36
    leonhua
    has no status.
    L Plate
    Join Date
    Aug 2006
    Posts
    37
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Hi guys, i bought a 2nd hand bike but don't like the plate number, wanna change a new plate, can? Roughly how much, i know for new bikes reg fee is only 100+ right

  37. #37
    Oreosworld
    has no status.
    Class 2B Oreosworld's Avatar
    Join Date
    Feb 2009
    Location
    Tampines
    Posts
    289
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Fass View Post
    Our Ref: LTA/CSV/F20.032.000/3384/1
    Date: 12-JUL-2004
    Tel: 1800-2255 582 (1800-CALL LTA)
    Fax: 6553 5329

    Dear Mr XXX,

    NUMBER PLATE REGULATIONS & MATERIAL USED
    FEEDBACK NUMBER: 153370

    Thank you for your enquiries of 30-JUN-2004.

    2. We wish to inform you that the technical requirements for motorcycle licence plates used in Singapore can be found in Rule 15 and Fourth Schedule of the Road Traffic (Motor Vehicles, Registration and Licensing) Rules.

    3. In summary, these rules specify that licence plates should comply with either of the following descriptions (colour code):

    a) Letters and figures are white, silver or light grey on a non-reflective black background for both front and rear; or
    b) Letter and figures are black on a white reflex-reflecting background for the front, and on a yellow reflex-reflecting background for the rear.

    4. The front licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 35 mm high, 25 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 5 mm;
    &copy; The space between the letters and figures shall be 10 mm;
    (d) A margin between the nearest part of any letter or figure and the top
    or bottom of the number plate shall be 5 mm;
    (e) A margin between the nearest part of any letter or figure and the sides of the licence plate shall be 10 mm.

    5. The rear licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 50 mm high, 30 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 10 mm;
    &copy; The space between the letters and figures shall be 20 mm;
    (d) A margin between the nearest part of any letter or figure and the top, bottom and sides of the licence plate shall be 10 mm.
    (e) For licence plate that consists of 2 rows of figures and letters, the space the 2 rows shall be 10 mm.

    6. No other figures or letters, design advertisement or ornamentation shall be placed near the licence plate in such a manner as to render it more difficult to read or distinguish the registration number of the motorcycle when in motion.

    7. Many licence plates used in Singapore are attached to plastic licence plates holders that contain wording and brand names. We have no objection to the fixing of licence plates with such holders if it meet the above requirements. In addition, the wordings on such holders shall not contain obscenities or profanities and shall not be derogatory seditious.

    8. As for your enquiry on the sticker type licence plate for the front, we have no objection to it so long as the above requirements are met. We hope we have addressed your enquiries satisfactorily, thank you.


    Yours sincerely,



    (SIGNED IN LOTUS NOTES)
    GOH SEONG HONG
    for MANAGER
    VEHICLE ENGINEERING DEPARTMENT
    VEHICLE & TRANSIT LICENSING DIVISION
    LAND TRANSPORT AUTHORITY

    Anyone know is this still valid? I just did a sticker number plate to the above dimensions for my NSR SP. Dont want to tio $70 fine

  38. #38
    Oreosworld
    has no status.
    Class 2B Oreosworld's Avatar
    Join Date
    Feb 2009
    Location
    Tampines
    Posts
    289
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Anyone knows?

  39. #39
    IvikaRazI
    is available
    TeePee IvikaRazI's Avatar
    Join Date
    Jun 2005
    Location
    Bedok Area
    Posts
    4,007
    Feedback Score
    0
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default

    If you are using sticker, it is not legal, due to size. If kena stop by TP...fine will depend on the mood of the TP. With sticker, I do not think you can do a big enough dimensions which is outline by LTA. You may wanna try to measure. It should be around 22cm to 25cm wide for a legal measurements. This also depends on your number plate, if got many 1111 then maybe can have a smaller dimension.
    * Suzuki GSR750
    ----------------------------


  40. #40
    d0n^
    has no status.
    SBF Lacer d0n^'s Avatar
    Join Date
    Jul 2003
    Location
    CCK
    Posts
    9,502
    Feedback Score
    0
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by leonhua View Post
    Hi guys, i bought a 2nd hand bike but don't like the plate number, wanna change a new plate, can? Roughly how much, i know for new bikes reg fee is only 100+ right
    some prices for no. plate retention/replacement can be found in the link below:
    http://www.onemotoring.com.sg/publis...le_number.html

    yr bike gets a new no. plate if u have another new vehicle under yr name to retain the old no. on & cost to u is $100.

    as for direct replacement of no. plate w/ new no. plate, i can't be too sure on the price.
    maybe $1,300?
    but there is a risk to take lar. in case the new no. is 'ugly' also.
    =[ Honda CBR150R ]=
    ....=[ R E P S O L ]=
    ....

  41. #41
    d0n^
    has no status.
    SBF Lacer d0n^'s Avatar
    Join Date
    Jul 2003
    Location
    CCK
    Posts
    9,502
    Feedback Score
    0
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by Oreosworld View Post
    Anyone knows?
    yes
    still valid.
    so long as the sticker no. plate means the correct dimensions, then it is ok.
    u need to note that the dimension for alphabets & numbering is different for front versus rear plate though.
    =[ Honda CBR150R ]=
    ....=[ R E P S O L ]=
    ....

     

     
  42. #42
    d0n^
    has no status.
    SBF Lacer d0n^'s Avatar
    Join Date
    Jul 2003
    Location
    CCK
    Posts
    9,502
    Feedback Score
    0
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by IvikaRazI View Post
    If you are using sticker, it is not legal, due to size. If kena stop by TP...fine will depend on the mood of the TP. With sticker, I do not think you can do a big enough dimensions which is outline by LTA. You may wanna try to measure. It should be around 22cm to 25cm wide for a legal measurements. This also depends on your number plate, if got many 1111 then maybe can have a smaller dimension.
    sticker sizes can be adjusted prior to printing mah.
    if u set it to the approved sizing, then no issues already right?


    but i must say that to create the rear no. plate in a single roll using approved specs = too long to look nice~
    =[ Honda CBR150R ]=
    ....=[ R E P S O L ]=
    ....

  43. #43
    RAKz
    Honda CBR600RR8
    TeePee RAKz's Avatar
    Join Date
    Nov 2007
    Posts
    2,158
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    If mine number is AX 00 B, can i make it single row for the rear but still using the standard size from LTA?

  44. #44
    sUuQr|e
    has no status.
    Class 2 sUuQr|e's Avatar
    Join Date
    Jun 2007
    Location
    la-singapour'
    Posts
    860
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    hey bros, is the euro text no. plate legal? i mean w/o the euro sticker thingy.....
    MY MEAN MACHINES

    01.2008 - 12.2009 - NSR150SP FT7**Z
    12.2009 - 4.2011 - L.C. 135 FBE 11**C
    4.2011 - 11.2013 - Super K.I.P.S FY 45** H
    11.2013 - ?.??.???? - YZF - R6 FBD 33** C
    12.2013 - ?.??.???? - Wave 125 FY 12** K

    #RTNW

  45. #45
    RAKz
    Honda CBR600RR8
    TeePee RAKz's Avatar
    Join Date
    Nov 2007
    Posts
    2,158
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by sUuQr|e View Post
    hey bros, is the euro text no. plate legal? i mean w/o the euro sticker thingy.....
    From wat i know even without the country sticker is illegal.

  46. #46
    Team_Commander
    get class 2 & 4
    TeePee Team_Commander's Avatar
    Join Date
    Feb 2009
    Location
    Bugis
    Posts
    1,880
    Feedback Score
    1 (100%)
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default

    is pasting a country's sticker beside the number legal or illegal???

    at the rear number plate....





    WTB: Wave 125 NF125MD coverset/ speedometer sensor . Let me know the details, Thanks

  47. #47
    Suede
    has no status.
    Class 2 Suede's Avatar
    Join Date
    Apr 2006
    Location
    Arozona sama sama ngan John Rambo
    Posts
    920
    Feedback Score
    1 (100%)
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)

    Default

    What if i go to the inspector and show the letter from this below and the inspector said this letter outdated year 2004 now 2009. How to justify? I enquiry with the chief inspector and was told off front license plate must be at least 1 meter above the ground. No bending of license plate and use screws and bolt.

    Originally Posted by Fass
    Our Ref: LTA/CSV/F20.032.000/3384/1
    Date: 12-JUL-2004
    Tel: 1800-2255 582 (1800-CALL LTA)
    Fax: 6553 5329

    Dear Mr XXX,

    NUMBER PLATE REGULATIONS & MATERIAL USED
    FEEDBACK NUMBER: 153370

    Thank you for your enquiries of 30-JUN-2004.

    2. We wish to inform you that the technical requirements for motorcycle licence plates used in Singapore can be found in Rule 15 and Fourth Schedule of the Road Traffic (Motor Vehicles, Registration and Licensing) Rules.

    3. In summary, these rules specify that licence plates should comply with either of the following descriptions (colour code):

    a) Letters and figures are white, silver or light grey on a non-reflective black background for both front and rear; or
    b) Letter and figures are black on a white reflex-reflecting background for the front, and on a yellow reflex-reflecting background for the rear.

    4. The front licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 35 mm high, 25 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 5 mm;
    &copy; The space between the letters and figures shall be 10 mm;
    (d) A margin between the nearest part of any letter or figure and the top
    or bottom of the number plate shall be 5 mm;
    (e) A margin between the nearest part of any letter or figure and the sides of the licence plate shall be 10 mm.

    5. The rear licence plates for motorcycle must also meet the following dimension specifications:

    (a) The letters and figures are 50 mm high, 30 mm wide and 5 mm broad;
    (b) The space between adjoining letters and between adjoining figures shall be 10 mm;
    &copy; The space between the letters and figures shall be 20 mm;
    (d) A margin between the nearest part of any letter or figure and the top, bottom and sides of the licence plate shall be 10 mm.
    (e) For licence plate that consists of 2 rows of figures and letters, the space the 2 rows shall be 10 mm.

    6. No other figures or letters, design advertisement or ornamentation shall be placed near the licence plate in such a manner as to render it more difficult to read or distinguish the registration number of the motorcycle when in motion.

    7. Many licence plates used in Singapore are attached to plastic licence plates holders that contain wording and brand names. We have no objection to the fixing of licence plates with such holders if it meet the above requirements. In addition, the wordings on such holders shall not contain obscenities or profanities and shall not be derogatory seditious.

    8. As for your enquiry on the sticker type licence plate for the front, we have no objection to it so long as the above requirements are met. We hope we have addressed your enquiries satisfactorily, thank you.


    Yours sincerely,



    (SIGNED IN LOTUS NOTES)
    GOH SEONG HONG
    for MANAGER
    VEHICLE ENGINEERING DEPARTMENT
    VEHICLE & TRANSIT LICENSING DIVISION
    LAND TRANSPORT AUTHORITY
    Yamaha SparkZ 110 (2004 to 2008)
    Yamaha X1-R 135 (June 2008 to Feb 2009)
    Gilera ST Runner 200 (Feb 2009 to I dun knw...)




    Cinta takkan datang, kalau tak dicari ... Cinta takkan dapat, kalau tak memberi ...

  48. #48
    meetersa
    has no status.
    L Plate
    Join Date
    Nov 2009
    Posts
    1
    Feedback Score
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by RAKz View Post
    From wat i know even without the country sticker is illegal.

    I accept with information:In the video it may be like that; the blood and gore details have been disabled for the same purpose, so everyone can watch how the game is like.

    __________________
    Taux simulation de prets immo bancaire | Credit simulateur de pret personnel | Simulateur de pret immobilier gratuit

  49. #49
    Darkness19
    19
    SBF Lacer Darkness19's Avatar
    Join Date
    Mar 2006
    Posts
    5,956
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    hey guys,anyone know whether having names at the bottom of the number plate,is it legal?
    Four Wheels Move The Body,Two Wheels Move The Soul

  50. #50
    xine
    has no status.
    P Plate
    Join Date
    Nov 2007
    Posts
    75
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Juz for effect, I re-pasted the number stickers of my number plate closely together, connecting at its ends. A TP warned me about it when I was stopped over for a visor offence. However, that number plate thing seems more like he's trying to impress the lady trainee TP who stopped me over in the first place, what with going around my bike n tryin to find fault anywhere he can.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •