-=BabyBlade=-(CBR)

[GuY]

Guy lets go track leh

 

KL, your "Guy" refer to me or refer to all of us?

[gladiat0r]

Guy lets go track leh

 

:cheeky: :cheeky:

[heisehui]

jus rtn from 1st link. go in 1pm jam 1 hr+ half hr under hot sun sweating half hr under rain -.-

[kianleong]

LOL! refering to u.. but still i wana go track with this bike be4 i really wana upgrade..

[kianleong]

:cheeky: :cheeky:

 

bro when is ur nxt session?

[gladiat0r]

dont forget the downside of going track..

take a look..

[gladiat0r]

bro when is ur nxt session?

 

should be a week before end of june i think..very busy few weeks for me..no time to warm up bike also....lol..

[kianleong]

dont forget the downside of going track..

take a look..

 

relac bro... i know the saying of dunnoe how to walk dun learn how to run.. will be very careful.. wont be too ambitous

[heisehui]

does most of the time their bike flip over cause by wad? tank slapper?

[kianleong]

does most of the time their bike flip over cause by wad? tank slapper?

 

i guess its the speed + the sudden twisting from left to right? not sure..

[gladiat0r]

does most of the time their bike flip over cause by wad? tank slapper?

 

its called a high side...mostly happens when rear tyre loses traction and starts to slide,and rider shuts throttle(natural reaction is to close throttle,which is wrong actually...should just maintain it).

 

actually very easy to put in words,but when ure there in that situation,so many things to think about,speed,rpm,braking points,other riders passing you,your lining,positioning,right gear....by the time u do all this and ur tyre starts to slide...haiz...i think u know wat happens la then..lol..

[Addictive]

Going DIY a set of H4 headlight relay and test it on my nc29 and the plan is to make an additional add-on relay with wire harness without cutting existing wire harness. However I have some difficulties in getting some of the parts and would be very appreciated if any brothers or sistas can share where to get the following parts.

 

1) H4 plug or connector

http://www.go.jeep-xj.info/Loom%2025.jpg

 

2) Fuse Holder

http://www.go.jeep-xj.info/Loom%2027.jpg

 

3) Bosch 5-pin Relay

 

4) Wire holder

http://www.go.jeep-xj.info/Loom%2001.gif

[kianleong]

Going DIY a set of H4 headlight relay and test it on my nc29 and the plan is to make an additional add-on relay with wire harness without cutting existing wire harness. However I have some difficulties in getting some of the parts and would be very appreciated if any brothers or sistas can share where to get the following parts.

 

1) H4 plug or connector

http://www.go.jeep-xj.info/Loom%2025.jpg

 

2) Fuse Holder

http://www.go.jeep-xj.info/Loom%2027.jpg

 

3) Bosch 5-pin Relay

 

4) Wire holder

http://www.go.jeep-xj.info/Loom%2001.gif

 

 

sounds chim to me

[wongwz84]

Good morning to all fellow bros and sis... Just woke up lo.... Nice going outing with u guys last night (long journey).... Especially the place near Tamp IKEA....

[gladiat0r]

Good morning to all fellow bros and sis... Just woke up lo.... Nice going outing with u guys last night (long journey).... Especially the place near Tamp IKEA....

 

how bro ur OHLINS suspension arrive already?

[kianleong]

travel till i reach home cramp

[wongwz84]

travel till i reach home cramp

 

haha.... but we had fun.....

[wongwz84]

travel till i reach home cramp

 

haha.... but we had fun.....

[GuY]

jus rtn from 1st link. go in 1pm jam 1 hr+ half hr under hot sun sweating half hr under rain -.-

 

Go in den nvr ask mi whether i wanna go in anot. Heehee...

[GuY]

LOL! refering to u.. but still i wana go track with this bike be4 i really wana upgrade..

 

Okok. I planning to go in aft my exam. Haha. But i go slow slow one. Go there learn. Haha.

 

sounds chim to me

 

V chim. I oso dun understand.

[gladiat0r]

GUY: wong say his OHLINS suspension arrive already and extreme equipment is testing it so that means we were both wrong la...there is OHLINS for our bike...so wait for him to fix and we'll see..but dunno why he pm me should just post here cos a lot of riders looking for ohlins too and wanna know the news..

[Addictive]

Go in den nvr ask mi whether i wanna go in anot. Heehee...

 

2nd link later?

[GuY]

2nd link later?

 

Wat time?

 

GUY: wong say his OHLINS suspension arrive already and extreme equipment is testing it so that means we were both wrong la...there is OHLINS for our bike...so wait for him to fix and we'll see..but dunno why he pm me should just post here cos a lot of riders looking for ohlins too and wanna know the news..

 

I check with him alrdy. It is still under testing. They are using other bikes' ohlins to see whether are they compatible to our bikes. Dunno whether can fit anot. Hopefully can fit, den it will benefit all of us. Haha. :angel:

[gladiat0r]

Wat time?

 

 

 

I check with him alrdy. It is still under testing. They are using other bikes' ohlins to see whether are they compatible to our bikes. Dunno whether can fit anot. Hopefully can fit, den it will benefit all of us. Haha. :angel:

 

other bikes ohlins? he told me he imported ohlins specifically for cbr 400..

[MaTrIx87]

haha.... but we had fun.....

 

wah bro changed ohlins ah?