where to get this IU bracket

[105FX]

Hi all, i came across this nighster with IU mounted on the right of the engine frame, anyone knows where i can get this done? my IU is mounted on my handle bar and it is butt ugly.

 

 

Thanks

[Liszt]

Hey man, go to First Motor. They have loads of brackets there. Can just ask them to fix it for you, just cost 15 bucks.

[rattlesree]

where is first motors bro?

[Hydher]

I have something similar. First option is to drill into the body frame. Looks better.

 

Second option is to use a bracket. Then Bend it to fit on the engine mount or exhaust nut.

Cons is, heat from the exhaust may/spoil the unit.

I use a bad conductor metal for the bracket.

Hope this helps.

[105FX]

Hey man, go to First Motor. They have loads of brackets there. Can just ask them to fix it for you, just cost 15 bucks.

 

thanks a lot Liszt, can you confirm is the shop at below address.

 

First Motor

#01-398, 3006 Ubi Rd 1, Singapore 408700

p: 67431911

[105FX]

Hi Hydher, interesting suggestion, do you mind sharing a photo of that. thanks

[Ariess]

thanks a lot Liszt, can you confirm is the shop at below address.

 

First Motor

#01-398, 3006 Ubi Rd 1, Singapore 408700

p: 67431911

 

 

yes.

and basically they can fab watever bracket u want.

so making a trip down there will actually be better den looking at pics

jus my 2 cents

[105FX]

Thanks ariess.

[Hydher]

Hi Hydher, interesting suggestion, do you mind sharing a photo of that. thanks

 

http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc6/251618_10150285935061397_633741396_9525853_5193421_n.jpg

[105FX]

thanks for the advise, went down to first motor yesterday, got the bracket fabricated and mounted to engine frame with clips, choose not to weld since paintwork will be affected and might have corrosion problems later. Damage is $25 and about 2hours, good job and and friendly staff .

[lnt]

Seng Kwang makes pretty decent stainless steel brackets on the spot. Cost abt $100 but the quality is very good

[Liszt]

Hi, that's the shop! They have all the necessary stuff!

 

thanks a lot Liszt, can you confirm is the shop at below address.

 

First Motor

#01-398, 3006 Ubi Rd 1, Singapore 408700

p: 67431911

[Liszt]

[ATTACH=CONFIG]211497[/ATTACH][ATTACH=CONFIG]211498[/ATTACH]thanks for the advise, went down to first motor yesterday, got the bracket fabricated and mounted to engine frame with clips, choose not to weld since paintwork will be affected and might have corrosion problems later. Damage is $25 and about 2hours, good job and and friendly staff .

 

Haha looks like you've it done! awesome!

[Hydher]

They to make it a little more parallel to the floor. Just an advice. cheers and nice job.

[tomsaw8]

[ATTACH=CONFIG]211497[/ATTACH][ATTACH=CONFIG]211498[/ATTACH]thanks for the advise, went down to first motor yesterday, got the bracket fabricated and mounted to engine frame with clips, choose not to weld since paintwork will be affected and might have corrosion problems later. Damage is $25 and about 2hours, good job and and friendly staff .

 

Just to check if there are any problems with the reading of IU when passing under erp gantry and carparks given the angle of the unit? Compared to the reference picture, yours is vertical rather than horizontal. Appreciate your feedback. Tks

[105FX]

Just to check if there are any problems with the reading of IU when passing under erp gantry and carparks given the angle of the unit? Compared to the reference picture, yours is vertical rather than horizontal. Appreciate your feedback. Tks

 

hi tomsaw, no issue so far with carparks and erp, it is not vertical but angled slightly, less than 45degree. let you know the angle once i get a chance to look at it closer.

[tomsaw8]

Thanks 105FX.

 

I am interested to do the same but to have the IU unit to be aligned with the frame. So it is likely to be angled more inwards.

 

Btw, what materials did First Motor use to fabricate the bracket for you? Stainless steel?

[105FX]

Just normal carbon steel, welded to form a T, then painted The whole thing black which match the frame. Will try to make the iu black once the warranty expires. First motor might not have stainless steel welding capability, do check before heading down.

[xcore]

tomsaw8 there might be some shops that does harley that have it ready made. I'm interested in getting one for my sporty too.

[tomsaw8]

tomsaw8 there might be some shops that does harley that have it ready made. I'm interested in getting one for my sporty too.

 

where might these shops be?

[xcore]

Twins performance, sunburst, sumsoon, sunhog, kustom, depends on whr you frequent.

[jamez]

Twins performance, sunburst, sumsoon, sunhog, kustom, depends on whr you frequent.

 

U can take out sunburst and twins. They don't have it.

[tomsaw8]

Twins performance, sunburst, sumsoon, sunhog, kustom, depends on whr you frequent.

 

Have heard of these shops recently...will check them out soon. Tks!

 

Btw, any indication on the likely damage on the wallet?

[105FX]

Hi tomsaw, as promised, the IU angle is 30degrees from the bike frame, right side view.

Are you asking abt servicing cost? Harley has a routine service charge , think I might still have it somewhere, let me know if u need it.

[105FX]

Hi tomsaw, as promised, the IU angle is 30degrees from the bike frame, right side view.

Are you asking abt servicing cost? Harley has a routine service charge , think I might still have it somewhere, let me know if u need it for sake of comparison.