paintwork problem

[CoStar]

due to my inexperience and lack of knowledge, i have destroyed a section of my 125z body. i places thinner thinking it would remove the glue stains but instead it crumpled the paintwork as well. i heck care and painted over it but still can be seen, the 'crumple' paint like face bo peng like that.

 

is there anyway i can remove it? any shops i can go to touch it up?coz i would like to respray it again.

 

thank u very much.

[oOQiangOo]

due to my inexperience and lack of knowledge, i have destroyed a section of my 125z body. i places thinner thinking it would remove the glue stains but instead it crumpled the paintwork as well. i heck care and painted over it but still can be seen, the 'crumple' paint like face bo peng like that.

 

is there anyway i can remove it? any shops i can go to touch it up?coz i would like to respray it again.

 

thank u very much.

 

resand all the fairing n spary new one if u wan buget one.. den go paste sticker nice liao lo.. hehe..

[CoStar]

which sandpaper to use? i know in sch there's diff types for diff materials..but the other time at this shop the aunty say anyone can.

[oOQiangOo]

those smooth ones... dun use those rough one.. it will spoil ur fairing oso...

[yd72]

those smooth ones... dun use those rough one.. it will spoil ur fairing oso...

 

Go any hardware shop, it will cost betw 40-50cents per paper. Buy low grades, low the grades the finer it is.

Sand all the paint job and wash the fairing suface and dry properly before doing any painting.

 

[X-ilED]

Go any hardware shop, it will cost betw 40-50cents per paper. Buy low grades, low the grades the finer it is.

Sand all the paint job and wash the fairing suface and dry properly before doing any painting.

 

 

 

 

bro do u know yur stuff?? check your own knowledge b4 giving advise.. the lower the grade the coarser it is!..

 

to the threadstarter.. get 3 different grades. starting from 400 , 600 and finish off with a 800.. coarse to fine..

[yd72]

Hey bro, pai seh........, it was hand over mind

Anyway alway go from coarse to fine, just feel the paper and you will know

 

 

[AR2 Performance]

due to my inexperience and lack of knowledge, i have destroyed a section of my 125z body. i places thinner thinking it would remove the glue stains but instead it crumpled the paintwork as well. i heck care and painted over it but still can be seen, the 'crumple' paint like face bo peng like that.

 

is there anyway i can remove it? any shops i can go to touch it up?coz i would like to respray it again.

 

thank u very much.

 

X-ilED is right on the sandpaper grades (the nos. represent sandpaper grain sizes) for fairings. As for the blinkers (just in case), the same old school DIY method is great for most minor falls.

 

For blinkers/mirrors (ABS type) :-

You can try start with 50, followed by the med 100~200 and finalize with the fine grades (500~800 depending of your blinker's/mirror's roughness) before you start spraying. Sanding with water or GT85 will great improve the results!!

[FREDDY]

for me i sand with water or wet sand paper

[hell-brat]

hey bro..try dis..sand with 80-150,den wen its quite even,sand wif 200,den wif 800-1000. wet sand with 800-1000 will make it smoother but time consuming. Cheers..

[CoStar]

thanks guys for ur advice. the only way to remove stickers nicely is by heat is it? and how many coats of paint do i have to put on to make it last? some parts that i sprayed scratch off easily. or must i add on any special laquer/coating?

[kurarensu]

thanks guys for ur advice. the only way to remove stickers nicely is by heat is it? and how many coats of paint do i have to put on to make it last? some parts that i sprayed scratch off easily. or must i add on any special laquer/coating?

 

try to peel of ur sticker by hand den u use petrol to wipe loh.. i always does tat.. but if ur paintjob is diy.. ur paint might discolour..

[AR2 Performance]

thanks guys for ur advice. the only way to remove stickers nicely is by heat is it? and how many coats of paint do i have to put on to make it last? some parts that i sprayed scratch off easily. or must i add on any special laquer/coating?

 

The are decals/stickers with non-residue adhesive (OEM decals are made of that & mostly from 3M), which should not poise a problem. Those without that properties (like the pump ron95 decal, it is made that way to deter end-user from peeling off), use GT85 to wipe the remaining residue off with a paper towel. Works for my past 2 bikes. Petrol works but it is very corrosive on laquer. Wipe long & hard enough & you will know why.

[coolone]

better sms alan law...He are good spray paint

[d3an_cain]

bro, just buy new panels @ jb lor if ur bike plain colours..

[--BuSa--YoNg--]

Bro o u can go down 2 bukit merah blk 1001 #01-51 they do respray n airbrush n 4 my advise dun use those can spray cuz is nt gd n look ugly,better send 2 respray shop n let them do e job cuz they more Pro as u r rite.......