[Group] Singapore BAJAJ Team (SBT)

[haktek]

i was watching this... http://www.youtube.com/watch?v=fNtvcweUroA

[lindavw]

tml reach loading bay wait for me maybe i will be late.

[saferider]

I had mistrusted this mechanic Jxxkie for more than 2 years servicing my bike.

 

Case 1

Gear shifting from 4 to 5 difficult after clutch cable replacement. Feedback to him for many times, instead of adjusting the clutch cable, he had claimed that the clutch rod and plates were faulty and replaced wrongfully at my own expense (clutch rod/plates and gasket). After replacement, problem still exists.

 

Case 2

My bike's rear tire, rubber damper and brake shoe were replaced with a new one. After replacement, my bike was draggy and stiff during riding due to the chain being over-tigthened, resulting the rear spocket and nuts became lossened and rubber damper was badly damaged and worn out.

 

Case 3

Frequent engine stalled during cold-start and stopping on the road after my carburettor was washed & tuned. Worst of all, the diagraphm was replaced unnecessary.

 

Case 4

My bike's front brake fluid resevoir was leaking and a new rubber enclosure was replaced. After replacement, the brake oil fluid still leaking. Feedback to the mechanic, I told him the metal top cover is the main problem, then the top metal cover and rubber enclosure (2nd time) was replaced at my own expenses.

 

Case 5

The air filter sponge were replaced several times after checking by the mechanic that the sponge was slightly black. As long as the filter sensor does not light out, why should the air filter be replace prematurely and unnecessary ?

 

Yesterday, I went down to UM to look for another reputable mechanic called Ah Long for second advise and servicing.

 

1) Gear shifting from 4 to 5 difficult.

2) Knocking sound during gear shifting and throttle opening.

3) Engine stalled during cold-start.

 

After diagnosed and checked by the veteran mechanic, Ah Long

 

Problem found

 

1) Clutch cable and gear shift were not adjusted properly.

2) Rear spocket and nuts were lossened, resulting the rubber damper badly damaged.

3) Air/fuel ratio was not tuned properly.

 

The mechanic (Ah Long) had successfully rectified those neligence problems that had been existing until yesterday and my bike was now perfectly 'OK' and operate as per normal.

 

I had feedback to the management and action had been taken against this neligence and sub-standard mechanic and will never allow him to service my bike anymore that will jeopadise not only myself but my wife's safety too.

 

Thanks to "Ah Long" the expert mechanic of UM

[Eliminator]

I had mistrusted this mechanic Jxxkie for more than 2 years servicing my bike.

 

Case 1

Gear shifting from 4 to 5 difficult after clutch cable replacement. Feedback to him for many times, instead of adjusting the clutch cable, he had claimed that the clutch rod and plates were faulty and replaced wrongfully at my own expense (clutch rod/plates and gasket). After replacement, problem still exists.

 

Case 2

My bike's rear tire, rubber damper and brake shoe were replaced with a new one. After replacement, my bike was draggy and stiff during riding due to the chain being over-tigthened, resulting the rear spocket and nuts became lossened and rubber damper was badly damaged and worn out.

 

Case 3

Frequent engine stalled during cold-start and stopping on the road after my carburettor was washed & tuned. Worst of all, the diagraphm was replaced unnecessary.

 

Case 4

My bike's front brake fluid resevoir was leaking and a new rubber enclosure was replaced. After replacement, the brake oil fluid still leaking. Feedback to the mechanic, I told him the metal top cover is the main problem, then the top metal cover and rubber enclosure (2nd time) was replaced at my own expenses.

 

Case 5

The air filter sponge were replaced several times after checking by the mechanic that the sponge was slightly black. As long as the filter sensor does not light out, why should the air filter be replace prematurely and unnecessary ?

 

Yesterday, I went down to UM to look for another reputable mechanic called Ah Long for second advise and servicing.

 

1) Gear shifting from 4 to 5 difficult.

2) Knocking sound during gear shifting and throttle opening.

3) Engine stalled during cold-start.

 

After diagnosed and checked by the veteran mechanic, Ah Long

 

Problem found

 

1) Clutch cable and gear shift were not adjusted properly.

2) Rear spocket and nuts were lossened, resulting the rubber damper badly damaged.

3) Air/fuel ratio was not tuned properly.

 

The mechanic (Ah Long) had successfully rectified those neligence problems that had been existing until yesterday and my bike was now perfectly 'OK' and operate as per normal.

 

I had feedback to the management and action had been taken against this neligence and sub-standard mechanic and will never allow him to service my bike anymore that will jeopadise not only myself but my wife's safety too.

 

Thanks to "Ah Long" the expert mechanic of UM

 

I also had some bad experience with him but it was also rectified yesterday.Bro were you the one with the white and red pulsar head?

[saferider]

I also had some bad experience with him but it was also rectified yesterday.Bro were you the one with the white and red pulsar head?

 

No, my red pulsar with lots of reflective sticker on my top box and wear white TP-505 helmet.

 

My advise not to let him service your bike anymore.

 

Yesterday, I met one indian rider who was serviced by this sub-standard mechanic (Jxxkie) in the past and was told that he don't want him to service his bike anymore.

 

Look for better trusted mechanics like 'Ah Long' or 'Ah Tek' in UM.

[NoFishesAllowed]

None bro! .... But if you really want to scarifies your P200 for top speed, below are the list of 'racuuuun' (poison) that you need to do. What ever you do and if it is not in the list, then don't bother to ask for top speed lah bro ... we have discussed this matter and case closed since none have done it here .... what we done here are just minimal enhancing only!

 

but in Indonesia from our Prides bros .. they have prooven that our pulsar can be done from 180cc to up to 230cc.

 

My friend in Surabaya upgrade his engine power 180cc to 228cc .. while his friend .. you can check the list below

 

Spec from bro BJ (prides indonesia) as per November 09 ( 223cc) dyno result (Mototech Jogja) = 24,7dk @ 9200 rpm

 

- bore X stroke = 71 mm x 56,4 mm (piston Izumi Dome 71mm, Ymh Scorpio piston ring OS 100)

- Valve diameter = 34mm - 28,5mm (in/ex) branded 1NT valve stem dia = 5,5mm

- porting 30 mm (in), 26,5 (ex)

- Intake = cuctom made by specialist Londo

- Pj -mj = 38 - 138.

- CAM; -In: 44 BTDC.

77 (close)

Lift:9,3mm

-Ex; 77 (open)

44 (close)

lift: 9,5 mm

- Cam profile modified to work with “Japanese valve springs”

- CR = 11,8 : 1

- Carb = Mikuni TMX33

- Open Air Filter K&N

- Left coil = Protec V3 w/ ground strap off

- Right coil = Protec Ultimate

- Spark plugs = Splitfire TP430C x 2

- CDI Rextor LE (left) and CDI P200 std (right)

- Exhaust = full system by specialist Adie Sheldiez, Bdg

- Sprocket Ratio = 14/35

- Clutch springs = Helios

- Racing (spontaneous gas grip) = TDR

- Custom oil catch tanks & breather hoses by specialist Londo

 

http://i423.photobucket.com/albums/pp319/Jeskoneng/MasLondo1.jpg

 

 

For your info ... HVC and SC Gaban did enquire from them and was told unless you operate the engine all out then no point of talking TOP SPEED and POWER! .. we learnt a great lesson from our bros there ....

 

 

btw .. is that really you taking the bank on your avatar? ... if yes ..hmmm we have some common interest hahahahaha

 

 

icic.. i got wad u saying.. haha.. they manage to take out pulsar air box ? x.x

 

oo.. its not me.. its google come out one.. hahahaha

[husher]

No, my red pulsar with lots of reflective sticker on my top box and wear white TP-505 helmet.

 

My advise not to let him service your bike anymore.

 

Yesterday, I met one indian rider who was serviced by this sub-standard mechanic (Jxxkie) in the past and was told that he don't want him to service his bike anymore.

 

Look for better trusted mechanics like 'Ah Long' or 'Ah Tek' in UM.

 

So wat did the management do to him???

[NoFishesAllowed]

ohya.. btw.. brembo brake pump tt kira had was 16rcs... wads stocks rcs then?

[mjbs64]

ohya.. btw.. brembo brake pump tt kira had was 16rcs... wads stocks rcs then?

 

none .. cos stock no have click one ley ... rcs is ratio click system!

Edited September 19, 2010 by mjbs64

[NoFishesAllowed]

none .. cos stock no have click one ley ... rcs is ratio click system!

 

how can u describe the strength of the brembos then?

btw.. my brake fluid like leaking from the brake pump...isit cos the mech o=put too much fluid when change brake line?

[mjbs64]

how can u describe the strength of the brembos then?

btw.. my brake fluid like leaking from the brake pump...isit cos the mech o=put too much fluid when change brake line?

 

can post close up pics ... not sure the master cylinder for your ride using sealed gasket or rubber washer ... you need to check whether the cover loosed or misaligned. Can try to retighten the screws or cap. If still leakage than my suggest go to UM lah .. hmm Unique Motor I mean cos they are the one who sell the package.

 

btw .. is your brembo rcs? .. hmm at UM @ Toh Guan posts never stated ley? The pic also can't see the click dial clearly.. . just curious .

 

RCS something like this ..

 

http://www.superbiketoystore.com/sport/Brakes/Master-Cylinders/Brembo-16mm-RCS-Radial-Clutch-Master-Cylinder-Ratio-Click-System-/prod_3178.html

Edited September 19, 2010 by mjbs64

[NoFishesAllowed]

can post close up pics ... not sure the master cylinder for your ride using sealed gasket or rubber washer ... you need to check whether the cover loosed or misaligned. Can try to retighten the screws or cap. If still leakage than my suggest go to UM lah .. hmm Unique Motor I mean cos they are the one who sell the package.

 

btw .. is your brembo rcs? .. hmm at UM @ Toh Guan posts never stated ley? The pic also can't see the click dial.. . just curious .

 

RCS something like this ..

 

http://www.superbiketoystore.com/sport/Brakes/Master-Cylinders/Brembo-16mm-RCS-Radial-Clutch-Master-Cylinder-Ratio-Click-System-/prod_3178.html

 

 

 

im using stock brake pump now.. hahah.. haven save enuf to buy brembo...

 

to speak of saving.. anyone got job intro... something flexible tt i can do even when school reopen?

[mjbs64]

im using stock brake pump now.. hahah.. haven save enuf to buy brembo...

 

to speak of saving.. anyone got job intro... something flexible tt i can do even when school reopen?

 

ohhh .. wonder who must have taken it during the 'sales rush' hehehe ... ok stock I think the problem surface like mine, visit UM and regasket the master cylinder reservoir cap and ask them to check the kit pump too just to make sure all in good condition.

Just to aware you, the brake fluid can damage the body paint on your ride .. take care.

Edited September 19, 2010 by mjbs64

[saferider]

So wat did the management do to him???

 

The mgmt had given Jxxkie a stern warning on his neligence and sub-standard services in expense of the customer's safety.

[SC Gaban]

sorry guys

after i came back today from the movie i was not feeling very well.

having headache

 

for those who wants to watch

here is some of my views on the movie

 

1) overall nto too bad,some humour inside the show too

2) the battle scenes can be improved,too many zoomed out views of the battles

3) the abilities of the gundams are not really shown

4) the ending(in my opinion) can be way better than it is now

 

Overall Rating: 8/10

Watch again?: Maybe

 

here are some of the pics that i took at west coast plaza this afternoon

Mecha Art Museum

 

Gundam Unicorn Destroy Mode

[ATTACH=CONFIG]175327[/ATTACH]

[ATTACH=CONFIG]175329[/ATTACH]

[ATTACH=CONFIG]175331[/ATTACH]

[ATTACH=CONFIG]175332[/ATTACH]

 

Gaogaigar

[ATTACH=CONFIG]175326[/ATTACH]

[ATTACH=CONFIG]175328[/ATTACH]

 

i watched the 10.30pm show. hmm... let me tell u mine perspective...

 

they were waiting for this dialouge to occur right? but they didnt expect it to be too soon. thats wat this movie is about. 2ndly, the entire movie was good, how and why they made the plot that way, its up to the creator of the movie. flower ending was kinda strange but its not important. wats important was the final note, "peace cannot be achived by force". the creator of the series was giving us a message. overrall, the movie was superb. left me thinking not about the movie, but wat is in the creators mind when he made this movie. yeah i like thE 00 QUATA!!!! and all the advanced FLAG and gundam mechs!!!!AAGHHHHHHHHHHHHHH!!!!!!!!!!!!

 

http://farm3.static.flickr.com/2804/4260025566_d7aa9f3a6c_o.jpg

http://www.pantip.com/cafe/chalermthai/topic/A8474714/A8474714-0.jpg

http://www.pantip.com/cafe/chalermthai/topic/A8474714/A8474714-1.jpg

Edited September 19, 2010 by SC Gaban

[NoFishesAllowed]

ohhh .. wonder who must have taken it during the 'sales rush' hehehe ... ok stock I think the problem surface like mine, visit UM and regasket the master cylinder reservoir cap and ask them to check the kit pump too just to make sure all in good condition.

Just to aware you, the brake fluid can damage the body paint on your ride .. take care.

 

icic... wads actually happening?

 

 

man... hope it dun damage the paint cos i just polish and wash the babe!

[SC Gaban]

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs708.snc4/62827_1592830108023_1454033989_31595245_3279512_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs348.ash2/62827_1592830348029_1454033989_31595251_1790545_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs645.snc4/60496_1592831228051_1454033989_31595257_5004757_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs325.ash2/60496_1592831308053_1454033989_31595259_7422236_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs665.snc4/60496_1592831348054_1454033989_31595260_1468581_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs665.snc4/60496_1592831468057_1454033989_31595263_4991733_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs355.ash2/63558_1592832388080_1454033989_31595267_1777237_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs335.ash2/61536_1592833788115_1454033989_31595275_5378428_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs335.ash2/61536_1592834068122_1454033989_31595281_6000088_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs655.snc4/61536_1592834148124_1454033989_31595283_2789990_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs337.ash2/61698_1592835668162_1454033989_31595288_57306_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs677.snc4/61698_1592835868167_1454033989_31595293_8037283_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs657.snc4/61698_1592835908168_1454033989_31595294_5883947_n.jpg

[mjbs64]

icic... wads actually happening?

 

 

man... hope it dun damage the paint cos i just polish and wash the babe!

 

the gasket leaks .. that's all ... sometimes it like that lah .. not your day after all. Wat I can recall is the leakkage started after I changed to SS braided hose... maybe during the bleeding process the mech did not sealed the cover correctly cos using the same gasket .. or before hand there's a leakage already .. hmmm not sure too but what ever now ok already lah ..

 

I think you better go UM .. universal motor since yours using stock one. Don't want to have the drop fluids landed on your paint ... Better safe than sorry!!

[alvinyansg]

ohhh .. wonder who must have taken it during the 'sales rush' hehehe ... ok stock I think the problem surface like mine, visit UM and regasket the master cylinder reservoir cap and ask them to check the kit pump too just to make sure all in good condition.

Just to aware you, the brake fluid can damage the body paint on your ride .. take care.

 

 

brandon bought it

[alvinyansg]

i watched the 10.30pm show. hmm... let me tell u mine perspective...

 

they were waiting for this dialouge to occur right? but they didnt expect it to be too soon. thats wat this movie is about. 2ndly, the entire movie was good, how and why they made the plot that way, its up to the creator of the movie. flower ending was kinda strange but its not important. wats important was the final note, "peace cannot be achived by force". the creator of the series was giving us a message. overrall, the movie was superb. left me thinking not about the movie, but wat is in the creators mind when he made this movie. yeah i like thE 00 QUATA!!!! and all the advanced FLAG and gundam mechs!!!!AAGHHHHHHHHHHHHHH!!!!!!!!!!!!

 

http://farm3.static.flickr.com/2804/4260025566_d7aa9f3a6c_o.jpg

http://www.pantip.com/cafe/chalermthai/topic/A8474714/A8474714-0.jpg

http://www.pantip.com/cafe/chalermthai/topic/A8474714/A8474714-1.jpg

 

i understand the story and all

it is a good show

just that like i posted maybe some aspects can be better

like the battle scenes

too bad 00 Qanta only came out in the last few mins of the show

yah the flower ending is weird

i think became a flower cos of setsuna's toughts with the help of tieria sync with the ELS

and gundam raphael also wasted

don't want to spoil the movie for those haven watch

anyway i don't mind watching the movie again

anyone interested?

 

gaban did you get the 00 Qanta model?

[SC Gaban]

i understand the story and all

it is a good show

just that like i posted maybe some aspects can be better

like the battle scenes

too bad 00 Qanta only came out in the last few mins of the show

yah the flower ending is weird

i think became a flower cos of setsuna's toughts with the help of tieria sync with the ELS

and gundam raphael also wasted

don't want to spoil the movie for those haven watch

anyway i don't mind watching the movie again

anyone interested?

 

gaban did you get the 00 Qanta model?

 

nope, but maybe someday. yeah wish i can watch it again. but will wait for the dvd. cos the screening is only for a week and i wil not be in sg dis weekend. u coming for the AFA thsi nov?

[Ah_Pet]

icic... wads actually happening?

 

 

man... hope it dun damage the paint cos i just polish and wash the babe!

 

ur bike 3 mths old.. still running in right?

maybe still under warrenty. [donno it still got or not, as it was taken out and in a few times]

[mjbs64]

brandon bought it

 

icic... wads actually happening?

 

 

man... hope it dun damage the paint cos i just polish and wash the babe!

 

ur bike 3 mths old.. still running in right?

maybe still under warrenty. [donno it still got or not, as it was taken out and in a few times]

 

don't think so .. cos the bike now using brandon's set I think, since kira's ori is with me ... kira pass me during his bike dies off and need to push start that time.

[khinwui]

No, my red pulsar with lots of reflective sticker on my top box and wear white TP-505 helmet.

 

My advise not to let him service your bike anymore.

 

Yesterday, I met one indian rider who was serviced by this sub-standard mechanic (Jxxkie) in the past and was told that he don't want him to service his bike anymore.

 

Look for better trusted mechanics like 'Ah Long' or 'Ah Tek' in UM.

 

noted..tks for sharing..

[alvinyansg]

nope, but maybe someday. yeah wish i can watch it again. but will wait for the dvd. cos the screening is only for a week and i wil not be in sg dis weekend. u coming for the AFA thsi nov?

 

icic

i not sure abt the afa

still when nearer the date then c how lor

missed the gundam exhibition today

came back from JB very tired did not go down compass pt