[Technical] Possible Solutions to your Phantom's Problem

[dogshit2]

Guyz do your phantom have little jerks when going at 120km/hr-140km/hr. something like no petrol felling... Little jerks for a few times then ok already..

[armani123sg]

hi bros, need some comments. my bike now got a problem with starting.

 

will have a tick tick sound when press ignition key. so according to the info, it should be battery weak. but i remember the battery changed less than 6 months only.

 

so i read on n e info states it might be rectifier, but that also less than 6 months old.

 

so do u all think is battery or rectifier?

 

the only difference to my bike now is i added LED. but i seldom switch it on. n also, i fixed up all e led on my own n when to mechanic n ask him help to help me connect to the power cause i not sure which one to fix to. he helped me connect the black wire from the led to the black wire in the left side chrome cover there and the other cable which is the red one, he connected onto a nut at the carbon starter there... might this be the problem??? is this set up draining e battery even without switching on the LED???

 

thanks bros. really appreciate ur help.

[VidaK]

hi bros, need some comments. my bike now got a problem with starting.

 

will have a tick tick sound when press ignition key. so according to the info, it should be battery weak. but i remember the battery changed less than 6 months only.

 

so i read on n e info states it might be rectifier, but that also less than 6 months old.

 

so do u all think is battery or rectifier?

 

the only difference to my bike now is i added LED. but i seldom switch it on. n also, i fixed up all e led on my own n when to mechanic n ask him help to help me connect to the power cause i not sure which one to fix to. he helped me connect the black wire from the led to the black wire in the left side chrome cover there and the other cable which is the red one, he connected onto a nut at the carbon starter there... might this be the problem??? is this set up draining e battery even without switching on the LED???

 

thanks bros. really appreciate ur help.

 

did he put a fuse...? or else there is a risk of short circuit...

[jtzx]

Problem 1: Exhaust emitting white smoke.

Reason: Engine oil is leaking into your chamber.

Solution: Pistol rings needs to be changed. Go to a bike workshop.

 

Reason: Your bike has a 2 stroke engine.

Solution: Its normal.

 

 

Problem 2: Engine stalls in heavy rain and unable / weak to start.

Reason: Spark plug could be getting wet by the rain causing it not not function

Solution: Remove, dry the spark plug and put it back properly. Go get the plug cap replaced.

 

Reason: Air fuel mixture may be too rich or lean.

Solution: Tune your carb to a leaner setting (turn screw anti-clockwise by 1/4).

 

Reason: Air leakages.

Solution: Change some of the rubber parts in tank.

 

 

 

Problem 3: Flat / Punctured Tyres

Solution: Try to inflate tyre with portable pump / bicycle pump then go bike or tyre shop. DO NOT ride on flat tyres as they may damage your tyre or wheel.

 

Solution: Use tyre repair kit, plug and pump = good to go. Kit can be bought at LAB.

 

 

Problem 4: Cannot / Hard to start bike

Reason: Battery may be weak (confirmed by a tick sound from the right side cover under the seat).

Solution: Push Start, and go get battery replaced.

 

Reason: Fuse may be blown.

Solution: Check Fuse. Fuse is located on right side of bike. Remove chrome cover under the seat and see. Look out for the centre of the fuse if its broken then FUSED lor. Change new one.

 

Reason: Bike is in gear, kill switch is on, no petrol.

Solution: Obvious.

 

Reason: Rectifier issue (despite new battery, bike soon becomes hard to start again)

Solution: Get mechanic to check with a voltage meter. Ah chong has one.

 

Reason: Petrol topped up too full - Don't laugh.

Solution: The petrol tank is not meant to be filled to the brim. Leave some space for air.

 

Reason: Water in petrol

Solution: Check that fuel cap is secure and no leaks

 

Others:

- Check ignition coil for sparks.

- Check magneto coil.

 

 

Problem 5: Cant go more den 80 km/h

Reason: You are not in the 6th gear

Solution: Down 1 time 1st gear. up 5 times to sixth gear

 

Reason: If confirm no 6th gear, gear box may be in bad shape

Solution: Go to a reputable workshop for a checkup, may need to over haul.

 

Reason: Insufficient Engine Oil (Very bad)

Solution: Check with dipstick as according to manual. Buy Engine Oil from petrol kiosk and top up.

 

Reason: Clutch may have been worn off (Engine reving very high but no power to go any faster)

Solution: Bike shop chance clutch.

 

Reason: Air fuel mixture too rich (Crazy vibrations at higher revs making it too uncomfortable)

Solution: Tune air fuel mixture leaner (Turn screw anti-clockwise 1/2 - 1 round)

 

Reason: Sprocket may be worn off

Solution: Change sprocket and chain.

 

 

Problem 6: Weird sound on my bike

Reason: Might be battery low. (Ticking sound on right side when start button depressed)

Solution: Push start, change battery

 

Reason: If sound is on gearbox side, chain may be too slack

Solution: Check your chain tension 1st. Should have about 2 to 3cm slack, tested at the center of the bottom span of the chain. Anything more, get it tightened.

 

 

Problem 7: - Exhaust Header got holes. Can repair?

Reason: Got one specific hole which is ok.

Solution: If unsure, post some pictures.

 

 

Problem 8: - Engine oil Dip stick broken (Broken part might be in engine)

Solution:

- Send to bikeshop.

- New dipstick costs around $11.

 

 

Problem 9: I have tried everything but to no avail. Any tow numbers please?

Solution:

- 67474740 Tiko cheong.

- 64560018 Wing Yap.

- 97384501 => Hello, you the tua chia one?

 

 

Problem 10: Engine Part Leaking Oil

Reason: Gasket Spoilt.

Solution: Bike shop, get it replaced

 

Reason: Cam chain tensioner spoilt.

Solution: Bike shop, get it replaced

 

 

Problem 11: When riding, bike lean to one side. Let go of handlebar, steering was shaky and wobbling

Reason: Might be steering cone problem.

Solution: Go bike shop to get it fixed. May also need re-alignment.

 

Reason: Wheel bearings spoilt.

Solution: Bike shop, get it changed.

 

Reason: Wheel alignment might have problem.

Solution: Bike shop, get it fixed.

 

 

Problem 12: Speedo is not working

Reason: The cable, or the gear at the end of the cable is spoilt or loose.

Solution: If loose, plug it back or tighten. Else needs replacement, go bike shop.

 

Reason: Speedo spoilt.

Solution: Bike shop.

 

 

Problem 13: My exhaust gives have a loud bang regularly. (Backfire)

Reason: Air fuel mixture too rich or too lean.

Solution: Retune the carb.

 

 

Problem 14: I lost my bike Key!!! What to do??

Solution: Go find the key smith.

 

Solution: If want to change ignition, look for Ah Chong (Planet) or scrapyard.

 

 

Problem 15: Bike pickup super slow. Even slower than small cc cars.

Reason: Clutch is worn

Solution: Change your clutch plates.

 

Problem 16: Damaged Exhaust: Header got hole / Muffler loose or dropping.

Solution: Header got hole can weld it up.

Solution: Muffler dropping can cut open the pipe and take it out but pipe will sound louder.

Solution: Alternatively can change the whole system, pipe + header, about 300+-.

 

Problem 17: Hard to kick the gears

Reason: Clutch is worn

Solution: Change or top up EO.

Solution: Change clutch plate.

 

Problem 18: When cold start, bike got "tick tick" sound

Reason: cam chain tensioner spoilt.

Solution: Change the cam chain tensioner.

Solution: If its rattling sound instead of "tick tick" sound, bring bike to mechanic.

 

Problem 19: Bike wobble for no apparent reason.

Reason: Might have problem with wheel bearings or tyre pressure.

Solution: Check that the tyre pressure is correct.

Solution: If tyre pressure is correct, most probably is the bearing spoilt.

Solution:Change new bearings.

 

Problem 20: In Vehicle Unit (IU) Spoilt.

Reason: There is a whole lot of reason, old, water seep in, etc etc.

Solution: But a second hand IU but need to transfer name.

Solution: Buy a new IU at $155.80 w GST.

Solution: Don't go into carparks or go through ERP.

 

Problem 21: Weak Battery.

Reason: Battery old. Cannot charge or hold properly. etc etc

Solution: Recharge the battery (Wet), Dry ones cannot be recharged?.

Solution: Most people change batteries instead of recharging.

Solution: If leaving bike alone for a long time, disconnect the battery to prevent further unnecessary drainage.

 

Problem 22: Need to step real hard for brake lights to light up.

Reason: There is a knob for adjustment, it might be loose

Solution: There is a black screw lookalike plastic knob( near the spring) located somewhere near the rear brake pedal. u can play around with the knob by turning to adjust the sensitivity of your rear brake when you apply brake.

 

Problem 23: IU Spoilt.

Reason: No reason in particular. If its spoilt, its spoilt.

Solution: Inspect at Vicom. Replace a new one if under warranty. If not, have to buy a new one at about $155 (Slim).

 

Problem 24: Where to get visor / assesories after 6.30pm.

Reason: No reason in particular.

Solution: Lim Ah Boy (Kelantan Lane around Jalan besar Hawker centre).

 

Problem 25: Can Phantom change headlights?

Reason: No reason in particular / cosmetics.

Solution: Yes. Can change and it all depends on your DIY / mech's skill.

Solution: http://www.pinkphantom.com - (Source to get nice headlights)

Solution: LAB - (Source to get nice headlights

[cazlex]

Guyz do your phantom have little jerks when going at 120km/hr-140km/hr. something like no petrol felling... Little jerks for a few times then ok already..

 

I am curious.... how u manage to go all up to 120-140kmph!!

Think my bike will vibrate like crazy even @ 100kmph!!

Haiz... but cant compare lah... mine is old bike n a noob rider... haha

[Hydher]

I am curious.... how u manage to go all up to 120-140kmph!!

Think my bike will vibrate like crazy even @ 100kmph!!

Haiz... but cant compare lah... mine is old bike n a noob rider... haha

 

 

mine is an fv plate. no problems achieving that.

[jB]

Problem 1: Exhaust emitting white smoke.

Reason: Engine oil is leaking into your chamber.

Solution: Pistol rings needs to be changed. Go to a bike workshop.

 

Reason: Your bike has a 2 stroke engine.

Solution: Its normal.

 

 

Problem 2: Engine stalls in heavy rain and unable / weak to start.

Reason: Spark plug could be getting wet by the rain causing it not not function

Solution: Remove, dry the spark plug and put it back properly. Go get the plug cap replaced.

 

Reason: Air fuel mixture may be too rich or lean.

Solution: Tune your carb to a leaner setting (turn screw anti-clockwise by 1/4).

 

Reason: Air leakages.

Solution: Change some of the rubber parts in tank.

 

 

 

Problem 3: Flat / Punctured Tyres

Solution: Try to inflate tyre with portable pump / bicycle pump then go bike or tyre shop. DO NOT ride on flat tyres as they may damage your tyre or wheel.

 

Solution: Use tyre repair kit, plug and pump = good to go. Kit can be bought at LAB.

 

 

Problem 4: Cannot / Hard to start bike

Reason: Battery may be weak (confirmed by a tick sound from the right side cover under the seat).

Solution: Push Start, and go get battery replaced.

 

Reason: Fuse may be blown.

Solution: Check Fuse. Fuse is located on right side of bike. Remove chrome cover under the seat and see. Look out for the centre of the fuse if its broken then FUSED lor. Change new one.

 

Reason: Bike is in gear, kill switch is on, no petrol.

Solution: Obvious.

 

Reason: Rectifier issue (despite new battery, bike soon becomes hard to start again)

Solution: Get mechanic to check with a voltage meter. Ah chong has one.

 

Reason: Petrol topped up too full - Don't laugh.

Solution: The petrol tank is not meant to be filled to the brim. Leave some space for air.

 

Reason: Water in petrol

Solution: Check that fuel cap is secure and no leaks

 

Others:

- Check ignition coil for sparks.

- Check magneto coil.

 

 

Problem 5: Cant go more den 80 km/h

Reason: You are not in the 6th gear

Solution: Down 1 time 1st gear. up 5 times to sixth gear

 

Reason: If confirm no 6th gear, gear box may be in bad shape

Solution: Go to a reputable workshop for a checkup, may need to over haul.

 

Reason: Insufficient Engine Oil (Very bad)

Solution: Check with dipstick as according to manual. Buy Engine Oil from petrol kiosk and top up.

 

Reason: Clutch may have been worn off (Engine reving very high but no power to go any faster)

Solution: Bike shop chance clutch.

 

Reason: Air fuel mixture too rich (Crazy vibrations at higher revs making it too uncomfortable)

Solution: Tune air fuel mixture leaner (Turn screw anti-clockwise 1/2 - 1 round)

 

Reason: Sprocket may be worn off

Solution: Change sprocket and chain.

 

 

Problem 6: Weird sound on my bike

Reason: Might be battery low. (Ticking sound on right side when start button depressed)

Solution: Push start, change battery

 

Reason: If sound is on gearbox side, chain may be too slack

Solution: Check your chain tension 1st. Should have about 2 to 3cm slack, tested at the center of the bottom span of the chain. Anything more, get it tightened.

 

 

Problem 7: - Exhaust Header got holes. Can repair?

Reason: Got one specific hole which is ok.

Solution: If unsure, post some pictures.

 

 

Problem 8: - Engine oil Dip stick broken (Broken part might be in engine)

Solution:

- Send to bikeshop.

- New dipstick costs around $11.

 

 

Problem 9: I have tried everything but to no avail. Any tow numbers please?

Solution:

- 67474740 Tiko cheong.

- 64560018 Wing Yap.

- 97384501 => Hello, you the tua chia one?

 

 

Problem 10: Engine Part Leaking Oil

Reason: Gasket Spoilt.

Solution: Bike shop, get it replaced

 

Reason: Cam chain tensioner spoilt.

Solution: Bike shop, get it replaced

 

 

Problem 11: When riding, bike lean to one side. Let go of handlebar, steering was shaky and wobbling

Reason: Might be steering cone problem.

Solution: Go bike shop to get it fixed. May also need re-alignment.

 

Reason: Wheel bearings spoilt.

Solution: Bike shop, get it changed.

 

Reason: Wheel alignment might have problem.

Solution: Bike shop, get it fixed.

 

 

Problem 12: Speedo is not working

Reason: The cable, or the gear at the end of the cable is spoilt or loose.

Solution: If loose, plug it back or tighten. Else needs replacement, go bike shop.

 

Reason: Speedo spoilt.

Solution: Bike shop.

 

 

Problem 13: My exhaust gives have a loud bang regularly. (Backfire)

Reason: Air fuel mixture too rich or too lean.

Solution: Retune the carb.

 

 

Problem 14: I lost my bike Key!!! What to do??

Solution: Go find the key smith.

 

Solution: If want to change ignition, look for Ah Chong (Planet) or scrapyard.

 

 

Problem 15: Bike pickup super slow. Even slower than small cc cars.

Reason: Clutch is worn

Solution: Change your clutch plates.

 

Problem 16: Damaged Exhaust: Header got hole / Muffler loose or dropping.

Solution: Header got hole can weld it up.

Solution: Muffler dropping can cut open the pipe and take it out but pipe will sound louder.

Solution: Alternatively can change the whole system, pipe + header, about 300+-.

 

Problem 17: Hard to kick the gears

Reason: Clutch is worn

Solution: Change or top up EO.

Solution: Change clutch plate.

 

Problem 18: When cold start, bike got "tick tick" sound

Reason: cam chain tensioner spoilt.

Solution: Change the cam chain tensioner.

Solution: If its rattling sound instead of "tick tick" sound, bring bike to mechanic.

 

Problem 19: Bike wobble for no apparent reason.

Reason: Might have problem with wheel bearings or tyre pressure.

Solution: Check that the tyre pressure is correct.

Solution: If tyre pressure is correct, most probably is the bearing spoilt.

Solution:Change new bearings.

 

Problem 20: In Vehicle Unit (IU) Spoilt.

Reason: There is a whole lot of reason, old, water seep in, etc etc.

Solution: But a second hand IU but need to transfer name.

Solution: Buy a new IU at $155.80 w GST.

Solution: Don't go into carparks or go through ERP.

 

Problem 21: Weak Battery.

Reason: Battery old. Cannot charge or hold properly. etc etc

Solution: Recharge the battery (Wet), Dry ones cannot be recharged?.

Solution: Most people change batteries instead of recharging.

Solution: If leaving bike alone for a long time, disconnect the battery to prevent further unnecessary drainage.

 

Problem 22: Need to step real hard for brake lights to light up.

Reason: There is a knob for adjustment, it might be loose

Solution: There is a black screw lookalike plastic knob( near the spring) located somewhere near the rear brake pedal. u can play around with the knob by turning to adjust the sensitivity of your rear brake when you apply brake.

 

Problem 23: IU Spoilt.

Reason: No reason in particular. If its spoilt, its spoilt.

Solution: Inspect at Vicom. Replace a new one if under warranty. If not, have to buy a new one at about $155 (Slim).

 

Problem 24: Where to get visor / assesories after 6.30pm.

Reason: No reason in particular.

Solution: Lim Ah Boy (Kelantan Lane around Jalan besar Hawker centre).

 

Problem 25: Can Phantom change headlights?

Reason: No reason in particular / cosmetics.

Solution: Yes. Can change and it all depends on your DIY / mech's skill.

Solution: www.pinkphantom.com - (Source to get nice headlights)

Solution: LAB - (Source to get nice headlights

Thank you

[munkit]

since you are new, have you tried oiling/lubricating your chain? Try with your engine NOT running, press/sit down on your seat and stand. Repeat that to confirm if sound is from suspension.

 

 

Might be rear wheel bearing if noise from rear. Or your suspension? Try and follow what I mentioned above to the other dude.

 

wad bout like wen i do free wheeling sometimes.. there a weird sound coming from my bike.. its like a goli(marble) sound, rolling somewhere in the bike..

is it the wheel bearing? but i don encounting anything from turing n stuffs.

[jtzx]

time to tighten your chain tension dude.. just drop by planet and ah chiong will know.

[Toyota23]

same dude... When I free wheeling I also Heard This Sound.. But I just hack care & ride .. But guess Some days I have to go Bike shop and tighten My chain already....

[Hydher]

correct.. its the chain.

[Toyota23]

Help Mate!!! I just came back after Washing my Phantom.. NOtice a NAIL Was in my Back Tyre & There is Air coming out bit by bit.... can u all guys help me Which bike shop to go on 2moro?? cause 2moro is a Holiday, Scare Waste trip going down.. I staying in the West now anyway.... :'(

[Hydher]

Problem 1: Exhaust emitting white smoke.

Reason: Engine oil is leaking into your chamber.

Solution: Pistol rings needs to be changed. Go to a bike workshop.

 

Reason: Your bike has a 2 stroke engine(ta150).

Solution: Its normal.

 

 

Problem 2: Engine stalls in heavy rain and unable / weak to start.

Reason: Spark plug could be getting wet by the rain causing it not not function

Solution: Remove, dry the spark plug and put it back properly. Go get the plug cap replaced.

 

Reason: Air fuel mixture may be too rich or lean.

Solution: Tune your carb to a leaner setting (turn screw anti-clockwise by 1/4).

 

Reason: Air leakages.

Solution: Change some of the rubber parts in tank.

 

Reason: Air filter clogged.

Solution : Get your air filter changed.

 

 

 

Problem 3: Flat / Punctured Tyres

Solution: Try to inflate tyre with portable pump / bicycle pump then go bike or tyre shop. DO NOT ride on flat tyres as they may damage your tyre or wheel.

 

Solution: Use tyre repair kit, plug and pump = good to go. Kit can be bought at LAB.

 

 

Problem 4: Cannot / Hard to start bike

Reason: Battery may be weak (confirmed by a tick sound from the right side cover under the seat).

Solution: Push Start(Clutch in after running with bike, release, give a quick throttle and clutch in) and go get battery replaced or ride to charge(if still can be charged).

 

Reason: Fuse may be blown.

Solution: Check Fuse. Fuse is located on right side of bike. Remove chrome cover under the seat and see. Look out for the centre of the fuse if its broken then FUSED lor. Change new one.

 

Reason: Bike is in gear, kill switch is on, no petrol.

Solution: Obvious.

 

Reason: Rectifier issue (despite new battery, bike soon becomes hard to start again)

Solution: Get mechanic to check with a voltage meter. Ah chong has one.

 

Reason: Petrol topped up too full - Don't laugh.

Solution: The petrol tank is not meant to be filled to the brim. Leave some space for air.

 

Reason: Water in petrol

Solution: Check that fuel cap is secure and no leaks

 

Others:

- Check ignition coil for sparks.

- Check magneto coil.

 

 

Problem 5: Cant go more den 80 km/h

Reason: You are not in the 6th gear

Solution: Down 1 time 1st gear. up 5 times to sixth gear

 

Reason: If confirm no 6th gear, gear box may be in bad shape

Solution: Go to a reputable workshop for a checkup, may need to over haul.

 

Reason: Insufficient Engine Oil (Very bad)

Solution: Check with dipstick as according to manual. Buy Engine Oil from petrol kiosk and top up.

 

Reason: Clutch may have been worn off (Engine reving very high but no power to go any faster)

Solution: Bike shop chance clutch.

 

Reason: Air fuel mixture too rich (Crazy vibrations at higher revs making it too uncomfortable)

Solution: Tune air fuel mixture leaner (Turn screw anti-clockwise 1/2 - 1 round)

 

Reason: Sprocket may be worn off

Solution: Change sprocket and chain.

 

 

Problem 6: Weird sound on my bike

Reason: Might be battery low. (Ticking sound on right side when start button depressed)

Solution: Push start, change battery

 

Reason: If sound is on gearbox side, chain may be too slack

Solution: Check your chain tension 1st. Should have about 2 to 3cm slack, tested at the center of the bottom span of the chain. Anything more, get it tightened. Also, lubricate your chain.

 

 

Problem 7: - Exhaust Header got holes. Can repair?

Reason: Got one specific hole which is ok.

Solution: If unsure, post some pictures.

 

 

Problem 8: - Engine oil Dip stick broken (Broken part might be in engine)

Solution:

- Send to bikeshop.

- New dipstick costs around $11.

 

 

Problem 9: I have tried everything but to no avail. Any tow numbers please?

Solution:

- 67474740 Tiko cheong.

- 64560018 Wing Yap.

- 97384501 => Hello, you the tua chia one?

 

 

Problem 10: Engine Part Leaking Oil

Reason: Gasket Spoilt.

Solution: Bike shop, get it replaced

 

Reason: Cam chain tensioner spoilt.

Solution: Bike shop, get it replaced

 

 

Problem 11: When riding, bike lean to one side. Let go of handlebar, steering was shaky and wobbling

Reason: Might be steering cone problem.

Solution: Go bike shop to get it fixed. May also need re-alignment.

 

Reason: Wheel bearings spoilt.

Solution: Bike shop, get it changed.

 

Reason: Wheel alignment might have problem.

Solution: Bike shop, get it fixed.

 

 

Problem 12: Speedo is not working

Reason: The cable, or the gear at the end of the cable is spoilt or loose.

Solution: If loose, plug it back or tighten. Else needs replacement, go bike shop.

 

Reason: Speedo spoilt.

Solution: Bike shop.

 

 

Problem 13: My exhaust gives have a loud bang regularly. (Backfire)

Reason: Air fuel mixture too rich or too lean.

Solution: Retune the carb.

 

 

Problem 14: I lost my bike Key!!! What to do??

Solution: Go find the key smith.

 

Solution: If want to change ignition, look for Ah Chong (Planet) or scrapyard.

 

 

Problem 15: Bike pickup super slow. Even slower than small cc cars.

Reason: Clutch is worn

Solution: Change your clutch plates.

 

Problem 16: Damaged Exhaust: Header got hole / Muffler loose or dropping.

Solution: Header got hole can weld it up.

Solution: Muffler dropping can cut open the pipe and take it out but pipe will sound louder.

Solution: Alternatively can change the whole system, pipe + header, about 300+-.

 

Problem 17: Hard to kick the gears

Reason: Clutch is worn

Solution: Change or top up EO.

Solution: Change clutch plate.

 

Problem 18: When cold start, bike got "tick tick" sound

Reason: cam chain tensioner spoilt.

Solution: Change the cam chain tensioner.

Solution: If its rattling sound instead of "tick tick" sound, bring bike to mechanic.

 

Problem 19: Bike wobble for no apparent reason.

Reason: Might have problem with wheel bearings or tyre pressure.

Solution: Check that the tyre pressure is correct.

Solution: If tyre pressure is correct, most probably is the bearing spoilt.

Solution:Change new bearings.

 

Problem 20: In Vehicle Unit (IU) Spoilt.

Reason: There is a whole lot of reason, old, water seep in, etc etc.

Solution: But a second hand IU but need to transfer name.

Solution: Buy a new IU at $155.80 w GST.

Solution: Don't go into carparks or go through ERP.

 

Problem 21: Weak Battery.

Reason: Battery old. Cannot charge or hold properly. etc etc

Solution: Recharge the battery (Wet), Dry ones cannot be recharged?.

Solution: Most people change batteries instead of recharging.

Solution: If leaving bike alone for a long time, disconnect the battery to prevent further unnecessary drainage.

 

Problem 22: Need to step real hard for brake lights to light up.

Reason: There is a knob for adjustment, it might be loose

Solution: There is a black screw lookalike plastic knob( near the spring) located somewhere near the rear brake pedal. u can play around with the knob by turning to adjust the sensitivity of your rear brake when you apply brake.

 

Problem 23: IU Spoilt.

Reason: No reason in particular. If its spoilt, its spoilt.

Solution: Inspect at Vicom. Replace a new one if under warranty. If not, have to buy a new one at about $155 (Slim).

[MrSingH]

Hi people,

Hopefully u guys can help me out.. Ive had a TA 200 FW plate for 3 odd years already. Recently, i had a major accident on the PIE when my bike chain DERAILED, got stuck in the rear tyre and i skidded on the expressway. Luckily i suffered minor scratches.. Since then ive been super paranoid regarding my bike chain. My new "heavy duty" bike chain started rattling again a month ago and i got it tightened.. and now its the same problem. I paid 100 for the chain set and sprocket change. Is this problem of chain loosening so common with the TA200 that its better for me to change to another bike? I seriously cannot live with the fear of that accident happening again

Thanks in advance guys, Appreciate it

[dragonforce]

phantom have this problem of getting a loose chain.. to prevent any mishaps, visually check your chain to make sure its not loose.. lube it often. learn how to tighten it yourself but make sure it isnt too tight..

[mepkoh]

Hi people,

Hopefully u guys can help me out.. Ive had a TA 200 FW plate for 3 odd years already. Recently, i had a major accident on the PIE when my bike chain DERAILED, got stuck in the rear tyre and i skidded on the expressway. Luckily i suffered minor scratches.. Since then ive been super paranoid regarding my bike chain. My new "heavy duty" bike chain started rattling again a month ago and i got it tightened.. and now its the same problem. I paid 100 for the chain set and sprocket change. Is this problem of chain loosening so common with the TA200 that its better for me to change to another bike? I seriously cannot live with the fear of that accident happening again

Thanks in advance guys, Appreciate it

 

as with every accident...have we learn anything out of it..??

we need to overcome the phobia and pick ourself up and move on..

 

the very first question is why did the chain derailed/break??

chains are not made to derailed/break like that...it is make to last until it is too long to use on the bike...

the normal reaction i would say ..hey u did not maintain the chains properly at regular intervals..like cleaning and lubbing it with the correct lub, adjusting the tension etc etc:dozed:

..bad sprockets/chains with bad tensions..are accidents waiting to happen.

 

anyway besides brakes and tyres..chains are the next likely to fail due to lack of maintenace and this part actually needed to be inspected , adjusted at regular intervals or after a ride in the rain or mud..and replaced worn parts when required..

 

Thanks for the wake up call MrSingh..

Edited May 2, 2009 by mepkoh

[Hydher]

Hi people,

Hopefully u guys can help me out.. Ive had a TA 200 FW plate for 3 odd years already. Recently, i had a major accident on the PIE when my bike chain DERAILED, got stuck in the rear tyre and i skidded on the expressway. Luckily i suffered minor scratches.. Since then ive been super paranoid regarding my bike chain. My new "heavy duty" bike chain started rattling again a month ago and i got it tightened.. and now its the same problem. I paid 100 for the chain set and sprocket change. Is this problem of chain loosening so common with the TA200 that its better for me to change to another bike? I seriously cannot live with the fear of that accident happening again

Thanks in advance guys, Appreciate it

 

I believe that you neglected your chain and failed to do a pre ride inspection and no, its not a common problem. Have not find the need to tighten my chain after proper lubrication and no gunning.

[jtzx]

any idea where do i jet my PK? wanna lub it and i finally got a jet. where do i rest the jet on? pipe? i just wanna lift the back up.

 

and yes.. maintence is a must. at least once a month.. gosh need to change my sproket soon ;-(

[chuan.z]

any idea where do i jet my PK? wanna lub it and i finally got a jet. where do i rest the jet on? pipe? i just wanna lift the back up.

 

and yes.. maintence is a must. at least once a month.. gosh need to change my sproket soon ;-(

 

At first I thought you wanna jet your Phantom carb... Then I realised that you meant jack. Yep, jack on pipe. I jack it near the heat shield there, but must make sure nothing heavy in box. If dunno/not sure where/how, next time go planet n observe...

[jtzx]

At first I thought you wanna jet your Phantom carb... Then I realised that you meant jack. Yep, jack on pipe. I jack it near the heat shield there, but must make sure nothing heavy in box. If dunno/not sure where/how, next time go planet n observe...

 

pardon me for the poor english spelling ;0

 

but i jack the pipe , bike will fall on the left and only the front wheels will be lifted up lez... how to just pop the back up and the front still touch the ground?

[chuan.z]

pardon me for the poor english spelling ;0

 

but i jack the pipe , bike will fall on the left and only the front wheels will be lifted up lez... how to just pop the back up and the front still touch the ground?

 

Haha. It's ok. For your case, it seems that your bike is tail heavy (forgot that you got 3 boxes!). Try emptying the boxes and if that still doesn't work, try putting some load on the handlebar.

[jtzx]

oh.. i remove my side boxes already.. so i get my friend to put some weight b4 i lub chain...

 

cause i seen koon do before. he can lift the back up with effort.. maybe need go back to him for lesson again.

[Hydher]

Go to planet and see it get done. Btw chuan, i decided not to get the scissors jack.Have learn the skill to push while lubing at the same time.

[jtzx]

is there a better way? share share lez... shi fu!

[jB]

This thread sure is useful