Troubleshoot ur Super4!

[rayhunter]

Aiyah!...this type of things also don't know Boon Siew say "OK"...we also "OK" lah...talk and suggest so much afterward something goes wrong we all kana "KO" by ah ray how?..that time we all Lan_lan as if we screwed his new bike...and ah ray asked us to pay & we all

 

Boon Siew mech should be the expert what...once awhile Japanese mechanic visit them and they also send occassionally their new employee for oversea training on certain bike..that's what I know lah..so.."normal"..we also normal lor. I clever hor

 

easy easy peace, me cool.

but agreed that if they say ok,at least i'm convinced.

The mech only handles honda bike and no other makes.

Look at the mech,most of them can be our grandfathers i guess,and not those young mech.so experience and advise could be valuable.

 

above are my personal views..

[eric78]

Q) EO is leaking from the drainage screw cap. What can i do to remedy other

than replace the EO sump? :cry:

[Winners]

Q) EO is leaking from the drainage screw cap. What can i do to remedy other

than replace the EO sump? :cry:

 

There should be a copper washer. Replace that first and see how.

[eric78]

There should be a copper washer. Replace that first and see how.

 

tink it has got nothing to do with the copper washer cos the screw can't be tighten now...tink the thread of the engine oil sump cover blunt le...

[Winners]

tink it has got nothing to do with the copper washer cos the screw can't be tighten now...tink the thread of the engine oil sump cover blunt le...

 

2 ways to modify:

 

1. Drill a larger hole over the existing one and re-tap again. You'll also need to change to a larger bolt of course.

 

2. Weld a nut over the existing hole and use a smaller bolt to match the nut.

 

However, whether it'll cheaper to replace a complete sump, I'm not sure. You'll have to check this out.

[eric78]

2 ways to modify:

 

1. Drill a larger hole over the existing one and re-tap again. You'll also need to change to a larger bolt of course.

 

2. Weld a nut over the existing hole and use a smaller bolt to match the nut.

 

However, whether it'll cheaper to replace a complete sump, I'm not sure. You'll have to check this out.

 

had got the sump cover replaced...thanx for all the useful advices...

[MIZI_82]

my s4 meter sumtimes working sumtimes not. wat it the meter thingy call? And how much? any one can help? Go bike shop, they say s4 no meter cable.

[Ah Pek]

my s4 meter sumtimes working sumtimes not. wat it the meter thingy call? And how much? any one can help? Go bike shop, they say s4 no meter cable.

 

Got two meter...which one?...speedo or rpm? "S4 no meter cable"...h=what does he mean?..he got no stock or telling you your model don't use cable?

 

Anyway...what S4 are you riding?

[MIZI_82]

Got two meter...which one?...speedo or rpm? "S4 no meter cable"...h=what does he mean?..he got no stock or telling you your model don't use cable?

 

Anyway...what S4 are you riding?

 

Its Speedo meter for vtec 2.he say my bike model dont use cabel..

[MIZI_82]

Any one can help?

[RideHard]

I think ur speedo meter is e electronic type for Spec2, got to chg ur probe sensor. how much? can't recall sorry, ask around for a gud deal den

[Ah Pek]

Any one can help?

 

Oh gosh..looks like everyone forgotten about you. So...it seem like an intermittent problem as you mentioned sometimes van sometimes cannot. Since there is no cable, I should think that it functions "electrically". What I can guess is that there must be a sensor or somewhat a detector unit that registered your wheel revolution and translated electrically in various level of voltage to give you your speed reading. I too believe that there is nothing spoiled but rather a loose connection somewhere.

 

Be daring..open up the meter and see any wiring that link to its circuit board and trace it down to the wheel axle area where there is something that register your wheel spin.

 

Sorry...can help more as my is non vtec using speedometer cable

[MrQuan]

guyss .. juz got a ver s .. everthing was normal for the pass few days but today wen i tried to start .. bike switch can on got light but wen i try to start the engine cant start no sound and the light went off wen i press the engine start button .. wat could be the problem ..

[Ah Pek]

guyss .. juz got a ver s .. everthing was normal for the pass few days but today wen i tried to start .. bike switch can on got light but wen i try to start the engine cant start no sound and the light went off wen i press the engine start button .. wat could be the problem ..

 

Definitly there is no current to crank your starter..a typical symptom of a dead battery and likely the rectifier may be affected. Go have the battery change and let the mech check your rectifier once the new battery starts the bike. The rectifier may be working but not charging up to specification to maintain the battery at constant.

[MIZI_82]

I think ur speedo meter is e electronic type for Spec2, got to chg ur probe sensor. how much? can't recall sorry, ask around for a gud deal den

 

Oh gosh..looks like everyone forgotten about you. So...it seem like an intermittent problem as you mentioned sometimes van sometimes cannot. Since there is no cable, I should think that it functions "electrically". What I can guess is that there must be a sensor or somewhat a detector unit that registered your wheel revolution and translated electrically in various level of voltage to give you your speed reading. I too believe that there is nothing spoiled but rather a loose connection somewhere.

 

Be daring..open up the meter and see any wiring that link to its circuit board and trace it down to the wheel axle area where there is something that register your wheel spin.

 

Sorry...can help more as my is non vtec using speedometer cable

 

Thanks for your help guys.Appreciate it alot.

[moreara]

hi all..

I was travelling at a speed of 30-40km yesterday and i tried to "free hand".. Den the handle bar shake frm left to right.. i wud sumtimes do dat b4 installing a box and the "shaking" problem doesn't occurs.. but after installing a box, the problem happens.. Is dat wat u guys meant of "tank slap"? ma bike is rather new.. 10 mths old.. no accident b4.. Izzit a need for a steering damper to rectify tis problem.. Need some advice.. thankz in advance..

[BuckBros]

Hi to all S4 riders,

 

I got this problem whereby i am unable to start my bike sometime and i need to push start it. It occurs to me for 5-6 times so far and I got no idea why it cant start. I am riding a Super4 version s. Hope you guys can solve my query!! Thanks in advance.

[moreara]

dudes.. ani1 wit any solution to ma problem???

[biting_point]

dudes.. ani1 wit any solution to ma problem???

 

it's like that when you had a box installed.. a steering damper only can minimise the problem..

 

other methods to minimise it:

balancing of your wheels,

change steering cone,

change wheel bearings..

 

may all help a bit..

 

but why wanna free hand???

 

Tank Slap..

[moreara]

i was only trying to see if the handling was ok or not.. i wen bikeshop yesterday and dey tighten ma handle.. but the problem still there.. dey say its normal.. i juz tot it wud be too early too experience tis 'problems' since ma bike is onli 10 months old.. niway, thanks bro biting_point 4 ur pointers.. appreaciate dat..

[kevin_hu]

hi, so u found solution for interme speedometer problem? mine one also happen same thing. pls advice, thanks

[WRfreak]

hi guys ... ive currently bought a S4 Ver s ... err.. just a few days back onli... er.. for the first three days i could start at one time pressing.. now when i press.. then starter seem makin it start.. unless i give it some oil then can start?? anyone can advice... and i notice the headlight is always on.. issit possible i can off the headlight off.. or something to switch it off? possible?.. any advice?

[loyjwe]

i also have the same problem. initailly i only need 1 press to start my engine in the morning but now dunno why need 3-4 times. any clue?

[WRfreak]

anyone who willing to advice about the following problems? thx

[loyjwe]

is it confirm brake pad gone liao if have squeaking sound when apply?