Yamaha TZM 150 Riders

[imben]

my battery is always running low after i switch on my neon light, and it takes a long time to charge back to 12v. i am not very sure izzit e rectifer or what, i change e battery few months back and e rectifer is still in working condition. i don know whats wrong with it.

[hohosaint]

Originally posted by imben@May 02, 2007 04:24 pm

my battery is always running low after i switch on my neon light, and it takes a long time to charge back to 12v. i am not very sure izzit e rectifer or what, i change e battery few months back and e rectifer is still in working condition. i don know whats wrong with it.

Using wet or dry?

 

If dry, install a voltmeter.

 

Wet wise, just ensure the level is above the minimum level.

[imben]

Originally posted by hohosaint@May 02, 2007 04:28 pm

Using wet or dry?

 

If dry, install a voltmeter.

 

Wet wise, just ensure the level is above the minimum level.

i using dry, i have a voltmeter but spoil. hahas

but how come my battery charge so slow? is because of the recitifer?

[hohosaint]

Originally posted by imben@May 02, 2007 08:00 pm

i using dry, i have a voltmeter but spoil. hahas

but how come my battery charge so slow? is because of the recitifer?

what is your normal travel distance and rpm?

[imben]

Originally posted by hohosaint@May 02, 2007 11:05 pm

what is your normal travel distance and rpm?

hmm,travel distance hard to say, from my place to my school roughly *18k so total distance is *36k(expressway speed will be around 90-100 sometime 110). will also go rounding and slack around with friends,now i having school holiday so my full tank 200k can last me for 4-5days.rpm will be roughly *6-7-8 in expressway? normal road around *4-5-6? i not very sure about rpm. :sweat: all is without switching neon. i hardly switch on nowadays.

 

*roughly

[hohosaint]

Originally posted by imben@May 03, 2007 01:40 am

hmm,travel distance hard to say, from my place to my school roughly *18k so total distance is *36k(expressway speed will be around 90-100 sometime 110). will also go rounding and slack around with friends,now i having school holiday so my full tank 200k can last me for 4-5days.rpm will be roughly *6-7-8 in expressway? normal road around *4-5-6? i not very sure about rpm. :sweat: all is without switching neon. i hardly switch on nowadays.

 

*roughly

Last time there was one user call bear that installed neon light for his M too. I cannot remember whether its battery operating from another seperate terminal or same. I believe is different terminal. But he did not have such experience.

 

To narrow down the problem, get your voltmeter fixed.

[NUT]

Hi hohosaint.

[hohosaint]

Originally posted by NUT@May 04, 2007 03:46 pm

Hi hohosaint.

Elo

 

Kacau sianz. :S

[hohosaint]

Originally posted by tzm77@April 29, 2007 05:52 pm

how bout tis 1 how huch will roughly cost....

just need to replace all the honda's to yamaha

http://www.dreamgate.ne.jp/nsr/bikemonth/2005/may05_06tn.jpg

i always have an urge in Red Bull... lol.

 

And I did ask about this spray work... But bear in mind... Some wordings are better to have stickers than spray on... It just looks better and some are not available

 

http://img144.imageshack.us/img144/1576/37797537396cg0.jpg

 

 

 

This particular guy in malaysia wanted to sell his bike. So, the sport fairings looked very appealing to me. But unfortunately, he wanted to sell it off in a bulk... Too BAD!!!!!

 

http://img145.imageshack.us/img145/8224/img00368ezyy2.jpg

[imben]

Originally posted by hohosaint@May 04, 2007 03:41 pm

Last time there was one user call bear that installed neon light for his M too. I cannot remember whether its battery operating from another seperate terminal or same. I believe is different terminal. But he did not have such experience.

 

To narrow down the problem, get your voltmeter fixed.

ic, thx . i will go fix it. =)

[BlitZwing]

Originally posted by hohosaint@May 04, 2007 05:04 pm

i always have an urge in Red Bull... lol.

 

And I did ask about this spray work... But bear in mind... Some wordings are better to have stickers than spray on... It just looks better and some are not available

 

http://img144.imageshack.us/img144/1576/37797537396cg0.jpg

 

 

 

This particular guy in malaysia wanted to sell his bike. So, the sport fairings looked very appealing to me. But unfortunately, he wanted to sell it off in a bulk... Too BAD!!!!!

 

http://img145.imageshack.us/img145/8224/img00368ezyy2.jpg

wooohooo... finally after searching 4 hours on end..

found what i been lookin for

note the black stripe infront and the marlboro logo at the bike instead of a plain white box

 

http://www1.odn.ne.jp/~europark/photo2001/yamaha500_02.jpg

[imben]

whoah~ nice. wonder how much will he be selling if is a SG bike.hahas

do u guys know what type of meter bulb is tzm using? cause i wanna change the meter light to other colour.

[QuoVadis]

wow nut is still alive. awhwhhawa

[kelmo]

TZM brudders. need help. my tzm is down. i was riding on ECP then i heard a noisy knocking sound under the tank area. TrAnG - TrUnG- TraNG- TruNg worst still when i dropped gear it was noiser. Saddest part is now cannot start...likely scenario: 1)block scratched. 2) piston sure need to change if block changed. 3)conrod needs to be change. 4) al the other miscellaneous stuff like the rings and all that engine accessories crap la. TWO WORDS: Major Overhaul.

 

Now i need your help brudders. Recommend me a really good bike repair workshop for overhaul, engine servicing and tuning. Im living in the east, so be nice with the location too, if possible. What do you think if i went to either the Yamaha Service Centre at Paya Lebar or Atan Motor at Ubi in mind to repair?

 

Any way to tow my bike to JB?

 

Many many thanks in advance for the replies.

[imben]

Originally posted by kelmo@May 07, 2007 12:16 am

TZM brudders. need help. my tzm is down. i was riding on ECP then i heard a noisy knocking sound under the tank area. TrAnG - TrUnG- TraNG- TruNg worst still when i dropped gear it was noiser. Saddest part is now cannot start...likely scenario: 1)block scratched. 2) piston sure need to change if block changed. 3)conrod needs to be change. 4) al the other miscellaneous stuff like the rings and all that engine accessories crap la. TWO WORDS: Major Overhaul.

 

Now i need your help brudders. Recommend me a really good bike repair workshop for overhaul, engine servicing and tuning. Im living in the east, so be nice with the location too, if possible. What do you think if i went to either the Yamaha Service Centre at Paya Lebar or Atan Motor at Ubi in mind to repair?

 

Any way to tow my bike to JB?

 

Many many thanks in advance for the replies.

around 6 month ago i send my bike for overhaul, things i have done, new piston, piston ring and the whole conrode.block just polish . if not ..... the whole conrode quite expensive, total spend was $550. i don't know is cheap not? but i trust the mech. i done this overhaul at kaki bukit bikeworkz. but you can always check with the rest first before you make the decision. =) and before i send to overhaul, my bike also cannot start. the trang trang trang sound can be cause by alot of things, maybe piston ring and when my valve break few months back my bike also got the sound under the tank.

 

just my 20cent tots.

[hohosaint]

If my memory didnt fail me. Original piston costs only 60~80. It varies from package too... Like if you were to buy a block comes with piston even cheaper

 

I do know that conrod is expensive. But actual cost: I never replaced before

 

Block is Y1 around 100~200 plus. Sometimes really hard to tell.

Cylinder head 100 plus.

[supafly]

is devilish were here he would recommend to go bayi at theck thye.... but u must have deep pockets la.

[imben]

anybody willing to sell their extra set of stock endcan and stomach? or trade with my mod endcan and stomach

[supafly]

hahahahkz! y want to change to stock ah ben? wow... nowadays so bz man... no time for gath... hey if we are large enuff in numbers, maybe we can get featured in motor culture asia... hahahahahahakz!

[imben]

Originally posted by supafly@May 08, 2007 01:33 am

hahahahkz! y want to change to stock ah ben? wow... nowadays so bz man... no time for gath... hey if we are large enuff in numbers, maybe we can get featured in motor culture asia... hahahahahahakz!

keep seeing those people that i don't wish to see. get it? hahas

featured in motor culture asia? omg, awesome, but too bad not many M riders come forum.

[kelmo]

Originally posted by imben@May 07, 2007 04:06 am

around 6 month ago i send my bike for overhaul, things i have done, new piston, piston ring and the whole conrode.block just polish . if not ..... the whole conrode quite expensive, total spend was $550. i don't know is cheap not? but i trust the mech. i done this overhaul at kaki bukit bikeworkz. but you can always check with the rest first before you make the decision. =) and before i send to overhaul, my bike also cannot start. the trang trang trang sound can be cause by alot of things, maybe piston ring and when my valve break few months back my bike also got the sound under the tank.

 

just my 20cent tots.

bro imben.. so how was it after the overhaul? i think the price is ok when u come to think of it. with the full service and expensive parts. eh but when u polish the block, the piston size managed to find one that fits ah? care to provide me with the exact location of this bikeworkz workshop and the mechanic name? bros...what about planet at ubi? i heard alot about it... is it really good?

[imben]

Originally posted by kelmo@May 08, 2007 07:53 pm

bro imben.. so how was it after the overhaul? i think the price is ok when u come to think of it. with the full service and expensive parts. eh but when u polish the block, the piston size managed to find one that fits ah? care to provide me with the exact location of this bikeworkz workshop and the mechanic name? bros...what about planet at ubi? i heard alot about it... is it really good?

after the overhaul was terrible. hahas, cause need to run in. some say 2 stroke don't have to run in but i think is better in the sense that everything is new and should somehow let it run smooth first before you start dragging. polish block only need to polish the surface cause by those scratch, the piston size should be ok. bikeworkz is located at no.157, kaki bukit ave 1, shun-li industrial park, is right beside the kakibukit prison school. actually every mechanic is good, is only the bonding we have to them and the trust. for me i rather stay to one mechanic that i trust then run around to other shops that charge cheaper and do things not nice. where do you stay?

[supafly]

ben looking for tampines members ar.... hahahahah!

[hohosaint]

It is not recommended to sleeve down the block. The heat resistant will be reduced. If budget does not allow, sleeve down lor.

 

[imben]

Originally posted by supafly@May 09, 2007 03:57 am

ben looking for tampines members ar.... hahahahah!

hahas, no la. cause in his previous post he say that he live in the east side what, if possible i can also bring him down to the mech =) *peace

yesterday got TP road block at bedok res, lucky my friend told me and i went home the other way, one of my friend kena visor . lucky me.

i also change clutch plate and did setting and change the jetting, woohoo, the feeling is much more better respone better.