[Discussion] Super Four General Enquiry Thread

[boi_s]

anyone knows where to get the stock rear mudguard ?

[jtzx]

anyone knows where to get the stock rear mudguard ?

u can either buy OEM from Honda at $100++ or aftermarket from @vtec88 at $70++

[ki113r]

anyone knows where to get the stock rear mudguard ?

 

Check with LAB. Less than $50 if I rmb correctly.

[ki113r]

anyone knows where to get the stock rear mudguard ?

 

Check with LAB. Less than $50 if I rmb correctly.

[Moralez]

Guys need help any idea how much is a original fuel tank lock/cap??

[boi_s]

what could be the reason if we find engine oil leaking on the floor after parking? block gasket?

[ticks]

Maybe the drain plug crush washer. By right after every oil change need to change the plug washer. The washer acts as a seal once it's crushed by the tightened drain plug. Next time u change the plug, ideally u need to replace te crush washer. Or else the washer losses its sealing capability, leading to oil leak.

 

Or worse case scenario, the gundu mechanic tightened the drain plug with brute strength to show how much power he has, to the point of cracking the sump case.. Then oil leaks from the cracks.

 

Or u can go for the magnetic drain plugs that have a reusable washer.

Hope this helps.

[sealover]

hi any 1 know where can i buy super back box bracket? any intro rider?

[safshadows]

Good Evening Gentlemen,

 

do check out the link below as im selling off my spec 1. cheers!

 

http://www.singaporebikes.com/forums/showthread.php/411454-WTS-Honda-CB400-Super-4-Spec-1

[cabb]

Wat type of brake pads is recommended for better braking n how much does it costs?

 

Normally people will recommend EBC HH or BREMBO brake pads. You can get EBC HH from unique motorsports; not too sure for BREMBO brake pads thou.

 

Sent from my SM-N9005 using Tapatalk

[Cellardoor]

Not sure if this has been asked before...

 

Would like to get the opinions of those riding S4s with high mileage over 100k/150k and so on. Have you done valve clearance? How important is it?

 

If yes, was the condition really bad? I'm still contemplating if I should go ahead and do it at this moment (close to 170k) as it would take 3-5 working days and I need my bike as daily transport. Workplace is rather far.

 

Thanks..

[SimpleRider]

Not sure if this has been asked before...

 

Would like to get the opinions of those riding S4s with high mileage over 100k/150k and so on. Have you done valve clearance? How important is it?

 

If yes, was the condition really bad? I'm still contemplating if I should go ahead and do it at this moment (close to 170k) as it would take 3-5 working days and I need my bike as daily transport. Workplace is rather far.

 

Thanks..

 

If I'm not wrong our fellow S4 forumer Hair1 (or Hairi or Ha1r1, not sure how to spell it) has done valve clearance before.

can ask him for results.

if you west-sider even better, I think he is west-sider.

 

 

cheers!

[SimpleRider]

Not sure if this has been asked before...

 

Would like to get the opinions of those riding S4s with high mileage over 100k/150k and so on. Have you done valve clearance? How important is it?

 

If yes, was the condition really bad? I'm still contemplating if I should go ahead and do it at this moment (close to 170k) as it would take 3-5 working days and I need my bike as daily transport. Workplace is rather far.

 

Thanks..

 

If I'm not wrong our fellow S4 forumer Hair1 (or Hairi or Ha1r1, not sure how to spell it) has done valve clearance before.

can ask him for results.

if you west-sider even better, I think he is west-sider.

 

 

cheers!

[justforme]

Not sure if this has been asked before...

 

Would like to get the opinions of those riding S4s with high mileage over 100k/150k and so on. Have you done valve clearance? How important is it?

 

If yes, was the condition really bad? I'm still contemplating if I should go ahead and do it at this moment (close to 170k) as it would take 3-5 working days and I need my bike as daily transport. Workplace is rather far.

 

Thanks..

 

i'm actually quite keen to know too as i just hit 100k. was thinking of doing valve clearance too. i recently just did carb servicing only.

[chongczt]

Hi guys,

 

I've just changed my brake rotors, AGAIN after 6 months. My previous newly replaced OEM ones were warped within the first 2 months, suspected that its cause of overheating cause the rotors burns everytime after a ride. Now that I changed it again to the original one, it feels good, but after I rode back home and touch the rotors, they burned my fingers, exact same thing as before. I don't want them to warp again cause of overheating, anyone have any idea how to rectify this?

 

Things I've done previously:

Clean and service calipers, brake pistons

Replaced brake pads

Bleed brakes

Replace brake pump

 

I've done almost everything except changing the whole caliper.

[HaiR1]

Not sure if this has been asked before...

 

Would like to get the opinions of those riding S4s with high mileage over 100k/150k and so on. Have you done valve clearance? How important is it?

 

If yes, was the condition really bad? I'm still contemplating if I should go ahead and do it at this moment (close to 170k) as it would take 3-5 working days and I need my bike as daily transport. Workplace is rather far.

 

Thanks..

 

 

 

Come down for a chat

 

I explain to u in detail.

[HaiR1]

If I'm not wrong our fellow S4 forumer Hair1 (or Hairi or Ha1r1, not sure how to spell it) has done valve clearance before.

can ask him for results.

if you west-sider even better, I think he is west-sider.

 

 

cheers!

 

 

Yes bro

 

 

I did it when doing my full overhaul

[HaiR1]

Normally people will recommend EBC HH or BREMBO brake pads. You can get EBC HH from unique motorsports; not too sure for BREMBO brake pads thou.

 

Sent from my SM-N9005 using Tapatalk

 

 

"Branded" pad doesn't always mean it's good..

[cabb]

"Branded" pad doesn't always mean it's good..

 

Haha! Agreed. My sentiments too.

 

Sent from my SM-N9005 using Tapatalk

[enzo7781]

Hi guys, e indicator beside e engine oil alarm, thats e temp alarm is it?

[ghost92]

hi guys, am gonna receive a spec 1 this tuesday, would like to clear some enquiries, can the spec 1 have panniers and main stand installed? if yes, where and how much would it cost, i am also looking to get a pair of shroud and a bellypan. do let me know where i can get them. thanks!

i don't mind looking at 2nd hand items as well(depending if they're in good condition)

[ghost92]

hi guys, am gonna receive a spec 1 this tuesday, would like to clear some enquiries, can the spec 1 have panniers and main stand installed? if yes, where and how much would it cost, i am also looking to get a pair of shroud and a bellypan. do let me know where i can get them. thanks!

i don't mind looking at 2nd hand items as well(depending if they're in good condition)

[archpunk]

hi guys, am gonna receive a spec 1 this tuesday, would like to clear some enquiries, can the spec 1 have panniers and main stand installed? if yes, where and how much would it cost, i am also looking to get a pair of shroud and a bellypan. do let me know where i can get them. thanks!

i don't mind looking at 2nd hand items as well(depending if they're in good condition)

 

hey sorry man, but where did you purchase your spec 1? am looking for one as well. been surveying around singapore

[ghost92]

hey man,i got it from another forumer in the garage sales's used bike section

[Cellardoor]

hi guys, am gonna receive a spec 1 this tuesday, would like to clear some enquiries, can the spec 1 have panniers and main stand installed? if yes, where and how much would it cost, i am also looking to get a pair of shroud and a bellypan. do let me know where i can get them. thanks!

i don't mind looking at 2nd hand items as well(depending if they're in good condition)

 

Shoud and bellypan all can get at various places and shops. But...thus far to my understanding, no main stand for spec 1. I know