[Group] YAMAHA Rx, Rx-S & Rx-K

[seven7sin]

wanna just share wif u of wat happen today while riding back.

 

the nite b4 i do my own decarbonizing of pipe...i'm soo proud of it...even my dad nver done it himself b4..

 

today after a long ride...just 3 traffic light from home...suddenly a LOUD engine noise is heard...while riding, i tink...tat one doesnt comes from my bike...i look to the right..saw a Subaru WRX..must be from his exhaust pipe..

 

but after the car pass by....the sound is still heard...untill i turn to my pipe and saw my silencer was halfway out of the pipe....WTH!...

 

luckily it doesnt fall off and run over by other vehicle....den i realise..while fixing the silencer yest nite..i didnt tighten the screw soo much...

 

lucky me...just in fron the the RXK bike shop opp aunty shop..near eminint plaza...ask the uncle to fix the screw...$2 giv him lah....even thou i can do it when back home..but the sound of the pipe was...AWESOME!!!...lolz.

 

now i noe...why the silencer must be install...hehhehz

 

I tried to take out the silencer to "clean" the pipe too. Took out the screw but unable to take out the silencer..hahah..got stuck..

now my screw drop out..lost..the silencer still dun wan to come out after ridden in for months..hmmz

[zoobay]

I tried to take out the silencer to "clean" the pipe too. Took out the screw but unable to take out the silencer..hahah..got stuck..

now my screw drop out..lost..the silencer still dun wan to come out after ridden in for months..hmmz

 

bro you take out the back part of the exhaust .... so now the header is separated.

 

then you insert a long solid pole through the end where the header should be....

jus jam through the exhaust.... if you taken out the screw... then the silencer should come out.

sometimes becos of carbon build up, the silencer is stuck

[0401897D]

i tink its better for the screw to be stuck rather than loose and lost it while riding..

 

to make the "sound" louder, according to my younger bro...who mix wil the "illegal

mat motors...he says this...

 

translated to english" make the holes in the silincer bigger, do not cut short. if TP catch and check, den u can just say..u dunnoe..you bought from the bike shop already like tat"

 

no need to buy leo vince or whatever pipe..to make it louder...hheheehz.

[yeukeong]

u mean after doing all the necessary change... the chances of bulb blowing & socket melting is oso high becoz of the 6v regulator???

 

i pressume this regulator cnot b change...

 

Before I upgrade my lighting coil, everythings is fine. Only the head light no bright enough, change to higher watt bulb still not satisfy with it brightness.

After upgrade to RXZ lighting coil, i'm so happy to c all my bulb brightness is so great

3 Months down the road, meter bulb start to blow up, follow is the head light than the socket melt.

Asked a few senior mechanic, some said my regulator spoilt can only get original one at about S$30+. Some said change also no use 6V regulator not lasting becos of 12V battery. Some said 12V regulator also no use, who can guaranty that other electrical components will not be affected.

So I assume that in order to upgrade from 6V to 12V, the entire electrical system need to change!!!!!!!!!!!!!

[yeukeong]

I tried to take out the silencer to "clean" the pipe too. Took out the screw but unable to take out the silencer..hahah..got stuck..

now my screw drop out..lost..the silencer still dun wan to come out after ridden in for months..hmmz

 

bro you take out the back part of the exhaust .... so now the header is separated.

 

then you insert a long solid pole through the end where the header should be....

jus jam through the exhaust.... if you taken out the screw... then the silencer should come out.

sometimes becos of carbon build up, the silencer is stuck

 

ya, need a solid pole and a solid blow too. If ur silencer is badly corrored, u will hv a few pieces of silencer.

[seven7sin]

bro you take out the back part of the exhaust .... so now the header is separated.

 

then you insert a long solid pole through the end where the header should be....

jus jam through the exhaust.... if you taken out the screw... then the silencer should come out.

sometimes becos of carbon build up, the silencer is stuck

 

OIC..so must take out the back of the exhaust...ic..have not try out yet..!

 

 

 

ya, need a solid pole and a solid blow too. If ur silencer is badly corrored, u will hv a few pieces of silencer.

 

I wonder how many "pieces of silencer" I have..I doubt will have le..

I often see "oil" clog up at the end of the exhaust...so i dun think will corrode

[retromotoracer]

Asked a few senior mechanic, some said my regulator spoilt can only get original one at about S$30+. Some said change also no use 6V regulator not lasting becos of 12V battery. Some said 12V regulator also no use, who can guaranty that other electrical components will not be affected.

So I assume that in order to upgrade from 6V to 12V, the entire electrical system need to change!!!!!!!!!!!!!

 

ok... lets say we take the 2nd senario... change to 12v regulator... is it possible in the 1st place??? change to rxz regulator???

 

next... entire electrical system consist of

1.head light

2.tail light

3.signal light

4.meter/indicator light

5.horn

6.flasher relay

7.rectifier

8.lighting coil

9.battery

10.regulator

 

is that all??? anything else that we miss???

so theorically electrically it should work like a rxz!!! true???

 

btw: saw "pengantin" bike park at BPP just now!!! lord bear: nice handlebar & paintwork...

[yeukeong]

Wire Harness

Rectifier & Regulator (New RXZ combine 2 in 1)

Ignition coil Assy

CDI unit Assy

Charge Coil (Not sure can fit or not)

Left & Right Switch on Handle bar

 

Yes, theoretically if entire electrical system can be change, it should work like a rxz.

[0401897D]

Hi all,

 

bad news...the silencer fall out in the MIDDLE of SLE and being flatten by passing vehicles...

 

rode from woodlands to SIN MING (my workshop)with a Harley Bike Sound. sounds awesome but LTA cnfirm wont approve.

 

currenlt the workshop LENT me spare OLD original silencer for free i'm going again on saturday to change to a better one.

 

would anyone noes the agaration price of 2nd hand silencer...pay havent come in bah..

 

Please secure, screw, weld, elephant glue ur silencer properly.

 

[yeukeong]

How much is the original silencer? I brought a non original for about S$10 only.

[Lord Bear]

Silencer cheap only, won't cost u more than 15 buck.

 

Tomorrow is my big day. Wish me luck guys!

[zoobay]

Silencer cheap only, won't cost u more than 15 buck.

 

Tomorrow is my big day. Wish me luck guys!

 

 

 

Long Live Hitler!!!!!

[retromotoracer]

Silencer cheap only, won't cost u more than 15 buck.

 

Tomorrow is my big day. Wish me luck guys!

 

congrats bro... may u have a blissful marriage, insya'allah.

[sabrove]

Silencer cheap only, won't cost u more than 15 buck.

 

Tomorrow is my big day. Wish me luck guys!

 

All the best bro.. we'll see u on Sunday!!??

[0401897D]

Silencer cheap only, won't cost u more than 15 buck.

 

Tomorrow is my big day. Wish me luck guys!

 

Thanks

 

Pray the best for you.

 

say a lot of prayers b4 akad nikah..do it once do it rite.

 

:-)

[sabrove]

Kakis! Whoever going this Sunday, lets meet up at Bt Timah Al-Ameen, opposite Beauty World @ 1000hrs. Anything contact me sab (aka sabrove) @ 92396337. Meeting the tdubs pple also, so can go together².

[zoobay]

pls if possible,.... come to the wedding...

 

only happen once a year....

its not a meet up for showing bikes but a gathering of frens to wish a fellow fren passage to marriagehood...

 

even if your bike is rusty , nvr mod... cannot make it.....

its not the bike but the intention of going dat counts....

 

so pls come......thank you........

 

(bear better have nice food ah!!!!)

[Lord Bear]

I m so touched!

[zoobay]

I m so touched!

 

aku nak nasi ayam penyet, erdinger black satu,... Telor penyu.....

[MOS]

pls if possible,.... come to the wedding...

 

only happen once a year....

its not a meet up for showing bikes but a gathering of frens to wish a fellow fren passage to marriagehood...

 

even if your bike is rusty , nvr mod... cannot make it.....

its not the bike but the intention of going dat counts....

 

so pls come......thank you........

 

(bear better have nice food ah!!!!)

 

haha zoobay where got happen once a year sia? i think i meant once in a life time right? hahahaha

 

I m so touched!

 

bear bear i'm still trying to sort out my work schedule but i'll try my best to make it!! big day for you dude!!! enjoy every single second!

[welly]

fellas,ah hee told me that if i wana install a hella horn on my rxs,he's gona charge me abt a $100 + incl installation..is dat reasonable?pls advise

[906rider]

hi guys, i dont come here often as i would like coz im pretty busy .. anyways , asking a favor , anyone has an RXS 115 owner/repair manual or know where to get one?

 

can you please pm me , i might not get to read your reply coz ive been drowning with work

 

cheers

[retromotoracer]

hey guys... & lord bear

 

sorry... not sure if i can make it to the wedding!!! sending parents in-laws to jb pontian tmr morning.

 

till wat time will u guys be stayin lepaking??? i target to be home by noon... if i do... i'll join u guys... if anything i'll gv Sab a call...

[cerealkiller]

here's to bear's happily ever after. cheers!

[sabrove]

here's to bear's happily ever after. cheers!

 

CHEERS!!