[Group] YAMAHA Fazer

[AnAmIwEk]

Any one here knows where I can get lightech rearsets for fz1-s?

[sad_how]

https://sg.carousell.com/p/48942200/?ref=search&ref_query=FZ1%20rearset&ref_rank=1&ref_referrer=%2Fsearch%2Fproducts%3Fquery%3DFZ1%2520rearset

 

This might interest you.

[societybar]

Intermittent engine-cutout problems in my experience are usually electrical.

 

You could start with a simple solution that worked for me: spray WD40 down your ignition barrel, with a cloth underneath to catch what flows out. Run the key in and out, turn it off and on while flushing repeatedly with WD40 to clean out anything that could be in there causing a bad connection. Finally spray with some electrical contact cleaner (available at any DIY or hardware store).

 

You could try the same with your engine kill switch.

 

A bad connection in either of these would cause your engine to cut out. Of course, it could be something deeper in the wiring as well.

 

Another question: What are the other symptoms when your engine cuts out? Do your dashboard lights and meter stay on? Or does everything shut off completely?

Assuming the lights are on, does the engine crank when you press the starter? Or no response at all?

 

Indeed lo and behold it was the kill switch. Did throw in some wd40 and it worked like a charm! Thanks guys. You guys are a genius.

 

 

Sent from my iPhone using Tapatalk

[skudai]

Hi guys, im currently riding a 2002 FZS1000 Fazer gen 1, just wana ask which bike shop is reliable enough to do a top overhaul and rewiring. Thank you in advance.

[new86]

Looking for FZ06 S2 aftermarket end cans... 88081083

[SouLRidr1]

Hi all!

 

I have a 2002 Fazer 1000 which I need to scrap since COE is expired.

 

Is anybody here who

1. can help me to scrap (i am currently not in town, but it needs to be done soon)

2. want to rip off some parts - e.g. almost new tires

3. can recommend me somebody who will take over the scrapping for me.

[stwb1981]

Hihi all.... Just gotten a FZ6S...

Cheers

[Strawberrydonut]

no one active here oredy even the facebook i try adding also no reply

[stwb1981]

Hahaha that is sadz....

 

Used to be bustling here....

[Burnt]

is there a group chat available for FZ riders ?

[DEnSo]

hi all, just got a fz8s

 

intend to put on risers and wide handlerbars for a wider and pull back upright riding posture

kindly advise where is a good place to do it?

and also if the stock clutch cables, brake lines and throttle cables lenght can accommodate??

many thanks in advice!!

[fongswd]

HI all, I am looking for a Ohlins rear shock for my 2012 Fazer 800. Anyone has a pc to sell? Pls contact me at 90281095. Thanks

[wajarian]

Hi long time never visit this page. Can anyone tell me if I could change front fork of my FZ6 N to upside down one. Felt kind of heavy with conventional fork. What type is best fitted from which model.

Thanks

[pufferfis]

Hi long time never visit this page. Can anyone tell me if I could change front fork of my FZ6 N to upside down one. Felt kind of heavy with conventional fork. What type is best fitted from which model.

Thanks

 

I would suggest perhaps you could take a look at race tech suspension in usa to change the proper spring rate to your fork springs and gold valve cartridge emulator kit....

http://racetech.com/ProductSearch/2/Yamaha/FZ6/2004-09

 

you can find the ideal spring rate by keying your riding weight and riding preference to calculate the best spring rate for your weight....Starts with letter FRSP no something and something... and it said there the gold valve suitable for your bike is FEGV S4101 ....

 

you can buy these off amazon at good prices...and certain sellers from there have low shipping rates like below 10usd....

 

It comes with instructions showing you where to drill six 6mm or was it 8mm holes in both your damper rods and further on how long to cut new fork preload spacers for your forks..n how much fork oil level height you need ....If you got a motorshop wic you are comfortable with ...you can guide them or they follow your instructions.....

this is also a good time where you can get adjustable preload fork bolt from ebay...

 

https://www.ebay.com.sg/itm/41mm-CNC-Preload-Adjusters-Fork-Bolts-YAMAHA-FZ6R-FZ6-2009-2015-14-2-Pcs-5-Color/142438139274?hash=item2129f9858a:m:m4yj2aXq-N-NAcYlHMmIfJg

 

they reli help when you wanna service your forks....less tension when you take out the top bolt....

 

or alternatively you can go to a race tech technician shop for advice....so far I heard guan hoe at kaki bukit autobay have contacts for a race tech trained technician on call for appointment....or you can go fluid mechanics wic is the official race tech fella in singapore....

also you can change upgrade your rear suspension to something aftermarket perhaps?...nitron...penske?...ohhhlins...?hyperrpro?...

Edited November 28, 2017 by pufferfis

[subisisniki]

is there a group chat available for FZ riders ?

 

 

Yea, is there one?

[tee kong kia]

Any fazer 1,8,6 riders Here?

 

Sent from my SM-N920I using Tapatalk

[Luk0976]

Hi guys whats the best battery for fz1 n.battery flat not sure to charge or replace