-=BabyBlade=-(CBR)

[MaTrIx87]

Originally posted by godfire@April 18, 2007 02:10 am

hi all,,,jux now at CTE my bike rev rev then seem like the oil cannot go in then sunddenly the bike die off by itself ,,,after that i stop at the side ,m,y frend help me push start then ok le,,still can go,,after that we reach bugis ,i stop the bike and makan and i still can start the bike and still can ride home,,,,,what is the problem with the bike huh?any old bird blader can tell me?...sian

bro tink its ur fuel pump.. coz i juz changed mine had this problem too think it costed close to $100

[vin82]

Originally posted by xiaohei85@April 18, 2007 12:03 am

hello,

 

just change rectifier and magnetic coil, haiz bike dead half way when going back hm, ask u all arr

wat is the cos of rectifier n magnetic coil to burn ?? and hw long can my new coil n rect last ???

not a old bird blader here but think ur case might due to voltage problem or charging problem. The voltage charging might not sync with the battery resulting maybe in over charging or under charging. Check for the fuse if any has blown. Maybe from here might led to clearer answers.

[vin82]

Originally posted by FW1314A@April 17, 2007 05:43 pm

how to check whether the rectifier is working fine, or is about to be spoil?

can use a multimeter or voltage reader to check the charging power from the battery.

[Tronicans]

Originally posted by Zer0@April 17, 2007 04:25 pm

Cost for shims depends on your valve clearances. Have to get the clearances measured and work out what size shims you need and how many of them. If every shim needs to be replaced then it will obviously cost you a lot more than if just 1 or 2 are out of spec.

 

If you haven't had the valve clearances checked for a long time its likely to cost more!

 

Average price I would say about 250-300 to check and set all valve clearances.

How long does it take to do valve clearance? As in days or a few hours?

[Aalex82]

Originally posted by Tronicans@April 18, 2007 06:13 am

How long does it take to do valve clearance? As in days or a few hours?

it is better to leave it for a few days so that the mech can slowly check all the shims..

there are a total of 16 shims for him to check using microguage..

[Aalex82]

Originally posted by M@+r!X@April 18, 2007 02:46 am

bro tink its ur fuel pump.. coz i juz changed mine had this problem too think it costed close to $100

same here dude..

[ahboy535]

Pardon me everyone but what is a shim ? Wah lau...Baby balders still no firm meeting up ar ? All so dao or just pure busy ?

[ahboy535]

Y so quiet today ?

[ashzibit_69]

Guys, what is the machine price for a FM plate? Not inclusive of insurance and road tax.

[vin82]

Originally posted by ashzibit_69@April 18, 2007 09:06 pm

Guys, what is the machine price for a FM plate? Not inclusive of insurance and road tax.

my plate is FM but inclusive of everything including new tyres, new paint work, new chain and spoket. 5k..

[ahboy535]

Originally posted by vin82@April 18, 2007 09:42 pm

my plate is FM but inclusive of everything including new tyres, new paint work, new chain and spoket. 5k..

Wow worth it...Mine nothing L model also 5k++

[vin82]

Originally posted by ahboy535@April 18, 2007 11:06 pm

Wow worth it...Mine nothing L model also 5k++

where u brought ur bike? i brought at amk auto point industrial park 2A speedy..

[Qiang]

Originally posted by Tronicans@April 18, 2007 06:13 am

How long does it take to do valve clearance? As in days or a few hours?

i did it once at k&t before..it takes an approximate 2days..

 

If i done my valve clearance alrdy...how come the tic tic sound just dun goes off? The more i throttle, the sound gets louder and harder

[Qiang]

If you guys happen to have an engine dies off half-way due to battery insufficient to support yr electrical...Also it starts to backfire once u try to start again...then the rectifier is gone..

[billyfigo]

hey guyz my bike was recently damaged .fairing stolen exhaust broken .. i've just done some parts up .. but still needa do fairing . do u all know how much is it to mould in malaysia heard in pasir gudang its kinda cheap and good and one in masai 2 . can anyone help me thanks billy here 92788319.

[hafiz84]

Originally posted by billyfigo@April 19, 2007 01:15 pm

hey guyz my bike was recently damaged .fairing stolen exhaust broken .. i've just done some parts up .. but still needa do fairing . do u all know how much is it to mould in malaysia heard in pasir gudang its kinda cheap and good and one in masai 2 . can anyone help me thanks billy here 92788319.

hey billy if u gt the plc we go 2gether want..??

 

do fairing

[hafiz84]

hey bro, when i open throttle gt tic tic sound..

like ringing sound??

y? confused:

[Aalex82]

Originally posted by Qiang@April 19, 2007 11:11 am

i did it once at k&t before..it takes an approximate 2days..

 

If i done my valve clearance alrdy...how come the tic tic sound just dun goes off? The more i throttle, the sound gets louder and harder

hear from rhema, he said K&T purposely replace the shim and set the cam a bit loose..

cannot be too tight..

sometimes is not the shim that produce the tick sound..

worn header gasket oso play a part.

[Qiang]

Originally posted by Aalex82@April 19, 2007 03:20 pm

hear from rhema, he said K&T purposely replace the shim and set the cam a bit loose..

cannot be too tight..

sometimes is not the shim that produce the tick sound..

worn header gasket oso play a part.

do you know e approximate cost to change the 4 gasket for header? I believe the reason u explained as i notice the sound come behind my radiator..

[Qiang]

Originally posted by billyfigo@April 19, 2007 01:15 pm

hey guyz my bike was recently damaged .fairing stolen exhaust broken .. i've just done some parts up .. but still needa do fairing . do u all know how much is it to mould in malaysia heard in pasir gudang its kinda cheap and good and one in masai 2 . can anyone help me thanks billy here 92788319.

Just curious wat causes all these damage to yr bike?

[Aalex82]

Originally posted by Qiang@April 19, 2007 04:09 pm

do you know e approximate cost to change the 4 gasket for header? I believe the reason u explained as i notice the sound come behind my radiator..

that time i change for 929 cost 50 bucks..

i think yrs oso abt the same price..

one gasket cost abt 2 bucks..

is the workmanship ex.. hav to take out the whole exhaust out and fairing.. and radiator..

take 2 days to complete the job..

one day to replace gasket and put back everything..

after a ride, hav to go back to the shop for tighten of nuts to yr header..

cos cannot screw too tight or loose..

[ahboy535]

Originally posted by vin82@April 18, 2007 11:34 pm

where u brought ur bike? i brought at amk auto point industrial park 2A speedy..

bike production

[godfire]

All fix ,lucky it the open and close fuel plug spoil....CBR rock!!

[FW1314A]

hi all bladers. i hav a stock endcan, which i would like to hav a more hollow sound, is tht sch a thing call tong fully and partially tong pipe? will the tong pipe be penailise for illegal modification?

[Aalex82]

my previous bike oso hav a tong exhaust..

but not ka ton alot..

that y the sound not so obvious..