SBF MaxSym Cafe

[Coyote66]

Just have to monitor for any irregularity on battery usage meanwhile I'm disconnecting the batt for prolonged inactivity.

 

I just came back from two weeks holiday

Was worried

But came back started the bike and all is well

No problem for me

[danielling1981]

Erm, that's weird. My Iu is off of engine off. I'll verify again in the morning

 

Confirm, if i didn't start my engine, the IU do not have power. I tested by inserting my cashcard and there was no response at all UNTIL i turn on my engine.

 

@naim, yours is different?

[danielling1981]

Erm, that's weird. My Iu is off of engine off. I'll verify again in the morning

 

Confirm, if i didn't start my engine, the IU do not have power. I tested by inserting my cashcard and there was no response at all UNTIL i turn on my engine.

 

@naim, yours is different?

[naim]

Confirm, if i didn't start my engine, the IU do not have power. I tested by inserting my cashcard and there was no response at all UNTIL i turn on my engine.

 

@naim, yours is different?

 

yup different. mine is always on. i guess when they prepared ur bike, the connected it to the ignition instead of a constant live supply.

[Baal]

Hi, I have a question on maxi scooters. Prev on my steed, 1 prob I had was that when going over a bump, due to the forward pegs, I cant use my legs to relieve some pressure off my back like how I can on my prev super 4. Was wondering will I have this issue too on a maxi scooter ? because I observe that maxi scoots all have forward feet placing positions. And that could be a potential issue for me ( due to my not so strong lower back ) like what happened when I rode my Honda steed. Thanks.

[naim]

Hi, I have a question on maxi scooters. Prev on my steed, 1 prob I had was that when going over a bump, due to the forward pegs, I cant use my legs to relieve some pressure off my back like how I can on my prev super 4. Was wondering will I have this issue too on a maxi scooter ? because I observe that maxi scoots all have forward feet placing positions. And that could be a potential issue for me ( due to my not so strong lower back ) like what happened when I rode my Honda steed. Thanks.

 

yes u might face similar issues because even when u put ur feet on the flat floorboard area, most likely the knees are bent at 90 degrees with your thighs horizontal to the ground (basically ur legs forward), so will make it difficult to stand as well. unlike naked bikes where u legs are directly below ur seating area.

[Baal]

yes u might face similar issues because even when u put ur feet on the flat floorboard area, most likely the knees are bent at 90 degrees with your thighs horizontal to the ground (basically ur legs forward), so will make it difficult to stand as well. unlike naked bikes where u legs are directly below ur seating area.

 

Thanks bro.

[Pianoman]

you can wire the cig socket direct to the battery. put a fuse for safety.

 

That's what I did just yesterday. Except for the fuse part...LOL. Have to get a fuse.

Thanks.

[Coyote66]

Which reliable workshop should i go to do the following? Intend to do all this saturday.

 

Change my IU position from left to the centre of the bike

Install a new wind shield which i bougth from ebay

Buy a good and loud horn plus installation

[naim]

Which reliable workshop should i go to do the following? Intend to do all this saturday.

 

Change my IU position from left to the centre of the bike

Install a new wind shield which i bougth from ebay

Buy a good and loud horn plus installation

 

ACM or taihin?

[naim]

Heidenau K66 on the maxsym

 

 

The rear however is narrower than original (150 vs 160). feels so much more nimble. compound is softer, so ride is definitely better.

[Sonic]

Gathering session.

31/10, 8pm

Casuarina Prata at upper Thomson

[naim]

Gathering session.

31/10, 8pm

Casuarina Prata at upper Thomson

 

yes lai lai! don't shy shy come.

[yahoo]

gathering session.

31/10, 8pm

casuarina prata at upper thomson

 

ok see you guys at 8pm

[Coyote66]

ok see you guys at 8pm

 

Very happy to see u there

Pls bring ur giant voucher

We can deal there

 

On a separate note

Anyone can advise what r the things to change or service at 10,000 km

Bike currently at 9k km

Intend to service before going to thailand on 14-18 nov.

[naim]

Lol what giant voucher all.

 

10k km just engine oil, filter, and gear oil.

[Coyote66]

Lol what giant voucher all.

 

10k km just engine oil, filter, and gear oil.

 

Noted

 

Giant voucher cos Yahoo was selling

$220 value Giant voucher at $200

And i bought from him

[Sonic]

Next time go giant bring me along. I got 10% discount lol

[Coyote66]

Gathering session.

31/10, 8pm

Casuarina Prata at upper Thomson

 

reminder

no need to stay for long if cannot

just a few minutes will do to know fellow maxsym riders

put a face to the nicks here

[ghost]

Lol what giant voucher all.

 

10k km just engine oil, filter, and gear oil.

 

So every 10000km change EO, filter n gear oil? How much for these?

 

When need to change belt n rollers? Usually how much?

 

Sent from my GT-I9100 using Tapatalk

[naim]

So every 10000km change EO, filter n gear oil? How much for these?

 

When need to change belt n rollers? Usually how much?

 

Sent from my GT-I9100 using Tapatalk

 

Oil and filter every 5k km (though personally i find it better to chg oil every 3k and oil filter 6k)

 

Gear oil 10k km

 

Belt and rollers recommended 15k, but can be stretched to 20k safely. (+- $300 inclusive labour)

[ghost]

Oil and filter every 5k km (though personally i find it better to chg oil every 3k and oil filter 6k)

 

Gear oil 10k km

 

Belt and rollers recommended 15k, but can be stretched to 20k safely. (+- $300 inclusive labour)

 

wow, $300 for belt n rollers only? seems a little on the high side to me. But not difficult to change ourselves rite? Wonder where can find parts for Maxsym

[naim]

wow, $300 for belt n rollers only? seems a little on the high side to me. But not difficult to change ourselves rite? Wonder where can find parts for Maxsym

 

Parts alone will be in the region of $250. Labour depends on which shop. With the right tools, u can DIY like i do. Will save alot in the long run. Parts can get from Mah (agent) or Weda (parts supplier)

[topgearalwaysrock]

Finally, the MaxSym 600i ABS 565cc has been unveiled in EICMA. Hope it gets into production soon and gets here!!!

[naim]

Finally, the MaxSym 600i ABS 565cc has been unveiled in EICMA. Hope it gets into production soon and gets here!!!

 

looks good, except that they stuck with the single cylinder design. 600cc single will be really vibey. unless they can balance it out well. still lose out in terms of power and weight to silverwing600 though. so they have to make sure the pricing is done properly. if under 18k, not too bad. potentially my next upgrade.