[Group] S S R

[chlim]

i ask u ar. how much is it to service air filter? how to set the air flow and fuel flow? what about air ratio?(similar to air flow?)

 

anyone?

stk or KNN???normally bikeshop done tat at $10 but got ppl do at $5 be4.....as for air ratio need to hav a experience mech. to do tat to get d best result....

[xiaokang]

ic..wah..reserve got 3 litre ar...so much ar..

[xiaowen]

stk or KNN???normally bikeshop done tat at $10 but got ppl do at $5 be4.....as for air ratio need to hav a experience mech. to do tat to get d best result....

 

Noted. air ratio similar to air flow and fuel flow?

[chlim]

Noted. air ratio similar to air flow and fuel flow?

air flow can be adjust but for fuel flow need to replace main jet...don just change main jets cos need to change jet needles n needle springs as well......

[xiaowen]

ic..wah..reserve got 3 litre ar...so much ar..

 

ya reserve can last u quite some distance...

[euz]

air flow can be adjust but for fuel flow need to replace main jet...don just change main jets cos need to change jet needles n needle springs as well......

ok ok............

open a bike shop to repair n service ppl bike lah................

[euz]

home sweet home...................

[xiaowen]

air flow can be adjust but for fuel flow need to replace main jet...don just change main jets cos need to change jet needles n needle springs as well......

 

how much will the change of main jet, jet needles n spring be? a estimate amt?

[chlim]

how much will the change of main jet, jet needles n spring be? a estimate amt?

this so call dyno jet....sellin $250++ but w/out dyno run.....

[chlim]

ok ok............

open a bike shop to repair n service ppl bike lah................

:sian: .........

[chlim]

home sweet home...................

don upz my GS thread liao.....reply PM till :giddy:

[xiaokang]

thank bro..

[smiley73]

i ask u ar. how much is it to service air filter? how to set the air flow and fuel flow? what about air ratio?(similar to air flow?)

 

anyone?

 

wah not so easy

[xiaowen]

this so call dyno jet....sellin $250++ but w/out dyno run.....

 

does it mean all this --> main jet, jet needles n spring ? what is float pin? float pin = jet needles?

[xiaowen]

thank bro..

 

no problem

[xiaowen]

wah not so easy

 

haha i very stress. i dunno what is the problem with my bike.

[chlim]

does it mean all this --> main jet, jet needles n spring ? what is float pin? float pin = jet needles?

flaotin pins is to control from over flow.....normal 2 stroke wear out fast but 4 stroke can last long.....jet kit stage 1 onli hav needles,main jets(100-106),spring........

[chlim]

haha i very stress. i dunno what is the problem with my bike.

get a trust mach. to check is d best.....

[xiaowen]

get a trust mach. to check is d best.....

 

i got a mech, he say my bike is ok, no problem. i describe my problem to him. he say it is normal. i ask u guys, when moving off, when u open trottle and let go clutch fully, do you feel a power lag ( as in move and got smth pull back awhile need to open more trottle to overcome )... is it normal for all super4?

[chlim]

i got a mech, he say my bike is ok, no problem. i describe my problem to him. he say it is normal. i ask u guys, when moving off, when u open trottle and let go clutch fully, do you feel a power lag ( as in move and got smth pull back awhile need to open more trottle to overcome )... is it normal for all super4?

diff bike hav diff behavior.....need to check things to recify d problem....could be elect. flow,carb,valve etc.......if got mod be4 worst cos a lot mech don really know then anyhow mod......at d end create more problem to bike in long run...

[xiaowen]

diff bike hav diff behavior.....need to check things to recify d problem....could be elect. flow,carb,valve etc.......if got mod be4 worst cos a lot mech don really know then anyhow mod......at d end create more problem to bike in long run...

 

what is elect? flow i wondering what the problem. carb jus service and mech say float pin is working fine. valve shld be working fine. bike is fully stock according to previous owner.

[xiaowen]

mech say bike is ok. he say i too sensitive..

[chlim]

what is elect? flow i wondering what the problem. carb jus service and mech say float pin is working fine. valve shld be working fine. bike is fully stock according to previous owner.

electric flow...can cause ur plug to be faulty.....

[chlim]

mech say bike is ok. he say i too sensitive..

ok lo....new bike u also hope things in tip top condition......

[xiaowen]

electric flow...can cause ur plug to be faulty.....

 

ok thinking of doing grouding wire...