SBF Silverwings / HOM Cafe 2012

[echris108]

Why old jdm makan so much more fuel?

[SW9000]

JDM got different configuration than the FJS, just like the diff program setting of a Power Commander.

[SW9000]

Standard For FJS400:

5k - 90km/h

5.5k - 100km/h

6k - 110km/h

6.5k - 120km/h

7k - 130km/h

 

Anything different from this, then either there are changes to the transmission settings (rollers, clutch spring, etc) or it is a 600cc.

[Saintjo]

Can't see my rpm..block by iu

[OlieLove]

Hi bros. just got my hands on a second hand silverwing. Does anyone know of any lowered rear shocks? it's quite uncomfy to ride so high. thanks in advance!

[SW9000]

Hmm... SW seating high?

 

Original Rear Shocks installed or aftermarket?

If not sure, can post picture let us see see.

[OlieLove]

its a stock shock.

anyways, its a bit high cause i use to ride honda fusion before this and it is super duper low.

the change is quite drastic for me to adapt to the silverwing posture.

 

Hmm... SW seating high?

 

Original Rear Shocks installed or aftermarket?

If not sure, can post picture let us see see.

[Tanarthur]

Wonder is there any update on the SWT600 from Malker. Thanks

 

 

Let's just ride....

[SW9000]

Stock Rear Shock is the lowest height available.

No choice. Must get used to it cos most 400cc are about the same or higher.

 

 

its a stock shock.

anyways, its a bit high cause i use to ride honda fusion before this and it is super duper low.

the change is quite drastic for me to adapt to the silverwing posture.

[OlieLove]

thanks man. prolly gonna go cut the shocks abit ah.

[scoobydoo]

Stock Rear Shock is the lowest height available.

No choice. Must get used to it cos most 400cc are about the same or higher.

David, i tot you said the YSS shocks are shorter than the stock ones?

[SW9000]

David, i tot you said the YSS shocks are shorter than the stock ones?

 

Physical length is shorter.

However, not sure it will compress more like the Stock?

If compress only a bit, then might still seat higher then original.

[MaIkEr]

Wonder is there any update on the SWT600 from Malker. Thanks

 

 

Let's just ride....

Nope for now. Still having the burgie smile!

 

Sent from my D6653 using Tapatalk

[Tanarthur]

Nope for now. Still having the burgie smile!

 

Sent from my D6653 using Tapatalk

 

Ok ok. Thanks...

 

 

Let's just ride....

[mad_man]

Good morning Bro, anyone has HID installed in your Wing? Mind to share cost and where to install?

 

 

Sent from my iPhone using Tapatalk

[scoobydoo]

mod to HID? don't think can pass inspection

 

i've tried HIR (halogen infrared reflective film) bulbs bought from Limbat, very bright at 2300 lumens.

http://www.limbat.com.sg/categories/index/29

 

the HIR bulbs are very bright and visible from afar, but if you're looking for high temp WHITE colored headlight, it's not

[mad_man]

The HIR is plug & play?

 

 

Sent from my iPhone using Tapatalk

[ellamcoy]

Yesterday while moving off, there were some hard shaking vibration when I increased the throttle. While idling the rpm meter fluctuate between 1k-1.5k and the engine stalled at traffic lights

 

What is the possible issues and where is the best budget shop to fix it?

[SW9000]

There is no 'best' budget shop to fix it.

It takes knowledge and experience to solve problems and thus difficult to tag to a cost.

Either go to your favorite shop or go ACM.

 

Based on description, could be:

 

1. Stalling and idling problem - Vacuum cable loose/leak, spark plug failure, injector or air filter dirty or engine out of syn.

2. Shaking/vibrating when moving off - clutch/clutch bell issue or tire pressure.

[ellamcoy]

There is no 'best' budget shop to fix it.

It takes knowledge and experience to solve problems and thus difficult to tag to a cost.

Either go to your favorite shop or go ACM.

 

Based on description, could be:

 

1. Stalling and idling problem - Vacuum cable loose/leak, spark plug failure, injector or air filter dirty or engine out of syn.

2. Shaking/vibrating when moving off - clutch/clutch bell issue or tire pressure.

 

 

I see, good point bro!

 

ACM contact is 90220203 (Ah Choong) right? Located at 10 Kaki Bukit 01-22?

[scoobydoo]

The HIR is plug & play?

 

 

Sent from my iPhone using Tapatalk

yup... similar precautions during installation applies, e.g. never touch the glass bulb

 

http://limbat.com.sg/legacy/others_images/lights/hir-h7.jpg

[scoobydoo]

Yesterday while moving off, there were some hard shaking vibration when I increased the throttle. While idling the rpm meter fluctuate between 1k-1.5k and the engine stalled at traffic lights

 

What is the possible issues and where is the best budget shop to fix it?

the last time my FJS engine encounter similar symptoms ... no fuel going in

 

another possibility to consider... defective fuel pump?

[mad_man]

yup... similar precautions during installation applies, e.g. never touch the glass bulb

 

http://limbat.com.sg/legacy/others_images/lights/hir-h7.jpg

 

Mind sharing the cost?

 

 

Sent from my iPhone using Tapatalk

[ellamcoy]

the last time my FJS engine encounter similar symptoms ... no fuel going in

 

another possibility to consider... defective fuel pump?

 

Thank you bros for the advise!

 

Had visited ACM this morning at 8am but only to realize that they open at 11am

 

The intermittent loss in power and excessive vibration are actually caused by faulty spark plug!

Took Ah Choong only 60sec to figure out, i m utterly impressed!

 

They had also helped me in checking the horn due to loose cable connector and replaced

my coolant with Engine Ice. The mech had also voluntarily check my tires pressure without

me asking lol. Thank God and Holy Cow he found a 3inches nail stuck in my rear tyre! Got a worm

patch as well. What surprised me was really the bill

 

Some people make a living by burning holes in other's pockets/wallets and raping people mother;

this shop is simply making a honest living which warrant my future support, thanks

to our seniors here for the recommendation

[scoobydoo]

Mind sharing the cost?

 

yup... similar precautions during installation applies, e.g. never touch the glass bulb

 

http://limbat.com.sg/legacy/others_images/lights/hir-h7.jpg

think it was something like $70 a pair, $35 per bulb... might have changed

give Richard of Limbat a call @63381138, he happy happy maybe give you discount