[Discussion] Typical prices for Phantom repairs & mods

[sawfly]

Usually around 400 sgd. This would be labour cost and may not include parts, depending on motor shop. Typically items changed or cleaned will be at least piston ring, piston, cylinder surface etc. Best to comms with mechanic what he will do upon disassembly and if he charge extra for parts. Some don't.

[holyrider]

how much is the price for changing phantom 200 CDI ?

[ber]

i was thinking of trying my hand at clutch changing. whats the cost of changing at the shops? i need to buy springs. would like to know the cost to see if it is worthwhile diy.

[matthias76]

i was thinking of trying my hand at clutch changing. whats the cost of changing at the shops? i need to buy springs. would like to know the cost to see if it is worthwhile diy.

 

SALUTE...if you mean changing the clutch plates yourself. Clutch cables are much easier, and they cost in the region of $10ish iirc.

[sawfly]

Clutch plates change around 100-150 sgd, I can't recall. That was because my clutch basket was worn and have to be replaced also. Anyway they usually dont swap out the springs when they change the clutch plate set.

[ber]

Hi never tried this before but was thinking open and see. That's why if I can buy a scrap good condition bike can open n see n at the same time take the parts. Some of my parts are old.

 

Too much engine braking, use brake better. Will check the price and try my hand at changing if the shop charges too high.

 

Sawfly, the tachometer you bought from where? Thinking of getting

[The Gentlemen]

Hey guys, does anyone know where i can find any hard saddlebags or side panniers for phantom? And a drag bar as well

[matthias76]

Hey guys, does anyone know where i can find any hard saddlebags or side panniers for phantom? And a drag bar as well

 

Auntie Shop Ubi - First East Centre.

[calico]

Just did an overhaul to my phantom.

 

Chong changed many stuff for me in the engine. Very hard to put all here.

 

Mainly the piston is new, re-weld my block, chain cam, gasket etc..

 

Charged me 480 including tow. updated below

 

*Rear brake light relay wiring $12 @ Lee Huat Motor, near 10 Mile Junction

*Speedo Cable $17 @ Lee Huat

* Fuel Sensor $40 (Planet) custom 4 & above

* Battery $38 Yuasa / $38(plug and play) (LAB) / $35 (Planet) / $48 (Ah Koon) / $60 woodlands road carltex (7Ah battery)

* Steering cone $55-65

* Cam Chain Tensioner $55-60 (for tick tick sound at cold start), 65

* Cam Chain Tensioner + Cam Chain + Gaskets + O-Rings + Chex 9000 EO = $277 (Eng Sin Motor - cck ave 1)

* Cam chain: 80sgd, not incl left crank case cover gasket, cam chain sprocket cover o ring and gasket

* Front brake disc $45

* Tyres (metz lasertec) $160 front & back (Planet) / $170 (HKL) / $155 (Unique Motorsports) / $130 (LAB)

* Rear Tyre (Metz) $90 @ (Planet) / $89 (HKL)

 

* Chain $70-120 depending on type

* Chain + Sprocket - $140+/-

* DID O RING with Original Honda Sprocket - $140 (Planet)

* Chain roller (without screw insert) - $5 (LAB)

 

* Signal lights - depending on which type you like. $8-25.

* Signal bulb, headlight bulb - 1 $ (LAB, easy DIY) (add on: approved brighter ones for $8. bought from koon.)

* Brake light bulb - $2 (Planet)

* Speedo BackLight + Workmanship (Planet) - S$2

* Headlight - anywhere from $35 to 90 depending the type you like

* Spark plug - $2-20 [[ Replay once had his changed for S$2 ]]

* Engine oil - $6 -19 (jB got his lousiest EO for $3)

* Brake Pad $15-25

* Bleed and change brake fluid($10 each side)

* Air filter - $10

* K&N Air filter $85 (Unique Motorsports)

* Wheel ball bearings - $20-35 (depends on how mech chop u) jtzx: change for only $5 at planet

* Gear Shaft - $100 (planet)

* Clutch plate - $80 (Planet)

* Front fork (1 pair) - $330 (planet)

* Front fork seals (plus fork oil of course) - $65 (planet)

* Front fork tube (1 x) - $30 (planet) $60 x 01 now

* Rectifier - $75(new) $25(2nd hand) (planet)

* Coil - $180 (planet), original $220

* Rethreading of spark plug thread - between $35 - $45.

* left crankcase oil seal behind drive chain primary sprocket: $15

* Gasket - $30 (koon)

* Gasket @ Exhaust - $25 (Planet)

* Starter carbon - $60 (planet)

* Started Relay - $80 (Eng Sin Motor - cck ave 1)

* Front fender - $45 (original honda) ($28 at ah boy, DIY 4 screws only)

* Rear brake plate w/ pad $58 (planet)

* Rear brake caliper assembly, incl mounting bracket, honda original - $155 (planet)

* Rear brake disc - $80 (planet)

* Original rear suspension $180 (planet)

* Repair front brake pump (jam) and replace brake oil -$25 - (planet)

* Front brake pump - $50 (Unique motorsport) $70 08/11

* Front brake rebuild - $35 08/11

* Rear Brake Pump ($85) (planet)

* Overhaul: Piston+Ring+Block+Top gasket+EO+Plug - ($380) - (planet)

* Overhaul: new Piston+new Ring+repaired Block+new Top gasket+new Cam Chain + 4-5 smaller engine parts + EO+Plug + Tow - ($480) - (planet)

* Rear brake light 12 v 5w/18w $1 (planet)

 

* Clutch cable - $15 (planet) / $20 (ah koon)

* Throttle cable - $12 (planet)

* Front Brake/Clutch Lever - $8 each(planet)

* Balancer [the 2 silver thingies at the edge of your handlebars] - $15 (planet)

* Front fender -$45 (AMK HL motors)

* Spark plug cap - $18 (planet)

* regina gold chain, front & rear honda sprockets with installation at ah boy

* air suction valve - $60

* front brake pump + caliper + brake fluid - $60 (planet)

* side stand(2nd hand) (ong's motor at midview building) - $10 / brand new $20 (upper thomson road spc)

* Choke replacement - $18 (planet)

* Carb Adjustment screw + washers + spring - $9 (2nd hand at workshop along cck ave 1)

*IU unit base plate... for attaching to handbar.$20 (Jalan Bukit merah workshop)

*Chain roller guide - $5 DIY (buy from Eversuccess at Lembu Rd)

*Speedo casing rubber lining - $10 (Eng Sin Motor - cck ave1)

*Chain Guard - $30 (Eversuccess)

*Service Front Brake Caliper and change Brake Seal (4 x Oring) $45

* Coolant reservoir (TA 150) $28 @ Planet

 

Mods and Accessories:

 

* Steel brake Line 1 pc - SGD $80 (unique motors)

* Respray of bike, (front/rear mudguard + Tank) single color - $180 (H L Cycle)

* Wide handlebar (custom4 phantom type) - $38

* Wide Crashbar with mounting points for spotlights - $80

* Big Footrest - $60 madman - Pinkphantom.com

* Front\Rubber part - $5/piece @LAB

* Front\Metal base plate - $12/piece @LAB

* Rear\Eagle footrest - $25/pair @ LAB (just bought today, now is $30)

* Side box e21 - $90-180 / $180 as of April 2010 from LAB

* Zeus box 48L - $110 (Koon)

* Fuel tank - $382 contact madman or check http://www.pinkphantom.com/estore06.html

* Spotlights $35 a pair http://www.pinkphantom.com/estore11a.html

* Windshield $65-80

* Grips $10-120

* Chrome w/ rubber strips grips (LAB) - $25

* Mirrors $12(LAB) - $50 (jB got his, 8 bucks for small ones)

* Look-alike-original mirrors (shop beside LAB) - $20, LAB should be cheaper.

* small foldable square mirror - $45 (HKL)

* Saddlebags $98-190 madman - Pinkphantom.com

* Hazard light less than $10 if u fix&wire urself, $18-20 for mech installation [[ S$15 if Replay does it for you! ]]

* Relocating rear signals to license plate - $10 (planet)

* Relocating rear signals to license plate with bracket - $28 (LAB)

* Rear box $80-330

* Voltage stabiliser - $59-$120 depends

* Rider's ORIGINAL footrest (LAB) - S$18 per side, can be cheaper?

* Stainless steel screws for speedo, and side covers. 6 to change altogether. $1-$1.80 also bought from koon.

* washers to go at 50c each at regina

* Socket for supporting the head light - $15

* Bullet Headlight - $35 (LAB)

* Gear lever with rubber $20 at koon

* Chrome gear and brake levers set - madman

* Stebel Magnum 2 (Silver) w/o installation - $18-$20 (LAB)

* Daiso electric horns (pair) - $45 (planet)

* Phantom TA 200 gearbox - $540 (planet)

* Front fender the "mudflap"- $20 at koon

* Stebel Electric horn with nice hidden installation under front chrome cover- at koon $38

* Re-wrap seat- Starts from about $38 from Eugene saddledry, $25 basic one from Auntie Shop

* Spotlights on crashbar with installation- $35 at koon

* Crashbar- $65 from ah boy DIY

* Anchor and wide type crashbar - madman

* rear no. plate $10..first shop opposite rov..ubi

* 6" Risers - $80 from Auntie Shop in Ubi

[matthias76]

Calico - sounds ok to me. Your block got crack?

[jh23]

Hi guys! How much would it cost to have my wire done? My low beam not working but my highbeam working! Need to send for inspection soon

[ber]

Hi they do not check high low beam so far if you are worried about that. I think got head light can already. Have you checked your bulb?

[jh23]

no idea how to check the bulb :/ dont dare to touch scared spoilt. how much is changing the bulb or wiring if things gets complicated?

[matthias76]

Should be just the bulb fused. Worst case scenario is one of the relays under the left front chrome cover is kaput. Bulb $6 relay is $20

 

Sent from my GT-I9506 using Tapatalk

[ber]

Just did an overhaul to my phantom.

 

Chong changed many stuff for me in the engine. Very hard to put all here.

 

Mainly the piston is new, re-weld my block, chain cam, gasket etc..

 

Charged me 480 including tow. updated below

 

*Rear brake light relay wiring $12 @ Lee Huat Motor, near 10 Mile Junction

*Speedo Cable $17 @ Lee Huat

* Fuel Sensor $40 (Planet) custom 4 & above

* Battery $38 Yuasa / $38(plug and play) (LAB) / $35 (Planet) / $48 (Ah Koon) / $60 woodlands road carltex (7Ah battery)

* Steering cone $55-65

* Cam Chain Tensioner $55-60 (for tick tick sound at cold start), 65

* Cam Chain Tensioner + Cam Chain + Gaskets + O-Rings + Chex 9000 EO = $277 (Eng Sin Motor - cck ave 1)

* Cam chain: 80sgd, not incl left crank case cover gasket, cam chain sprocket cover o ring and gasket

* Front brake disc $45

* Tyres (metz lasertec) $160 front & back (Planet) / $170 (HKL) / $155 (Unique Motorsports) / $130 (LAB)

* Rear Tyre (Metz) $90 @ (Planet) / $89 (HKL)

 

* Chain $70-120 depending on type

* Chain + Sprocket - $140+/-

* DID O RING with Original Honda Sprocket - $140 (Planet)

* Chain roller (without screw insert) - $5 (LAB)

 

* Signal lights - depending on which type you like. $8-25.

* Signal bulb, headlight bulb - 1 $ (LAB, easy DIY) (add on: approved brighter ones for $8. bought from koon.)

* Brake light bulb - $2 (Planet)

* Speedo BackLight + Workmanship (Planet) - S$2

* Headlight - anywhere from $35 to 90 depending the type you like

* Spark plug - $2-20 [[ Replay once had his changed for S$2 ]]

* Engine oil - $6 -19 (jB got his lousiest EO for $3)

* Brake Pad $15-25

* Bleed and change brake fluid($10 each side)

* Air filter - $10

* K&N Air filter $85 (Unique Motorsports)

* Wheel ball bearings - $20-35 (depends on how mech chop u) jtzx: change for only $5 at planet

* Gear Shaft - $100 (planet)

* Clutch plate - $80 (Planet)

* Front fork (1 pair) - $330 (planet)

* Front fork seals (plus fork oil of course) - $65 (planet)

* Front fork tube (1 x) - $30 (planet) $60 x 01 now

* Rectifier - $75(new) $25(2nd hand) (planet)

* Coil - $180 (planet), original $220

* Rethreading of spark plug thread - between $35 - $45.

* left crankcase oil seal behind drive chain primary sprocket: $15

* Gasket - $30 (koon)

* Gasket @ Exhaust - $25 (Planet)

* Starter carbon - $60 (planet)

* Started Relay - $80 (Eng Sin Motor - cck ave 1)

* Front fender - $45 (original honda) ($28 at ah boy, DIY 4 screws only)

* Rear brake plate w/ pad $58 (planet)

* Rear brake caliper assembly, incl mounting bracket, honda original - $155 (planet)

* Rear brake disc - $80 (planet)

* Original rear suspension $180 (planet)

* Repair front brake pump (jam) and replace brake oil -$25 - (planet)

* Front brake pump - $50 (Unique motorsport) $70 08/11

* Front brake rebuild - $35 08/11

* Rear Brake Pump ($85) (planet)

* Overhaul: Piston+Ring+Block+Top gasket+EO+Plug - ($380) - (planet)

* Overhaul: new Piston+new Ring+repaired Block+new Top gasket+new Cam Chain + 4-5 smaller engine parts + EO+Plug + Tow - ($480) - (planet)

* Rear brake light 12 v 5w/18w $1 (planet)

 

* Clutch cable - $15 (planet) / $20 (ah koon)

* Throttle cable - $12 (planet)

* Front Brake/Clutch Lever - $8 each(planet)

* Balancer [the 2 silver thingies at the edge of your handlebars] - $15 (planet)

* Front fender -$45 (AMK HL motors)

* Spark plug cap - $18 (planet)

* regina gold chain, front & rear honda sprockets with installation at ah boy

* air suction valve - $60

* front brake pump + caliper + brake fluid - $60 (planet)

* side stand(2nd hand) (ong's motor at midview building) - $10 / brand new $20 (upper thomson road spc)

* Choke replacement - $18 (planet)

* Carb Adjustment screw + washers + spring - $9 (2nd hand at workshop along cck ave 1)

*IU unit base plate... for attaching to handbar.$20 (Jalan Bukit merah workshop)

*Chain roller guide - $5 DIY (buy from Eversuccess at Lembu Rd)

*Speedo casing rubber lining - $10 (Eng Sin Motor - cck ave1)

*Chain Guard - $30 (Eversuccess)

*Service Front Brake Caliper and change Brake Seal (4 x Oring) $45

* Coolant reservoir (TA 150) $28 @ Planet

* clutch gasket $7 LAB

* clutch cable $12 LAB

* Seat cover $15 LAB

* Throttle cable $ 15 LAB ( i think on high side)

* carb boot $25 LAB

 

Mods and Accessories:

 

* Steel brake Line 1 pc - SGD $80 (unique motors)

* Respray of bike, (front/rear mudguard + Tank) single color - $180 (H L Cycle)

* Wide handlebar (custom4 phantom type) - $38

* Wide Crashbar with mounting points for spotlights - $80

* Big Footrest - $60 madman - Pinkphantom.com

* Front\Rubber part - $5/piece @LAB

* Front\Metal base plate - $12/piece @LAB

* Rear\Eagle footrest - $25/pair @ LAB (just bought today, now is $30)

* Side box e21 - $90-180 / $180 as of April 2010 from LAB

* Zeus box 48L - $110 (Koon)

* Fuel tank - $382 contact madman or check http://www.pinkphantom.com/estore06.html

* Spotlights $35 a pair http://www.pinkphantom.com/estore11a.html

* Windshield $65-80

* Grips $10-120

* Chrome w/ rubber strips grips (LAB) - $25

* Mirrors $12(LAB) - $50 (jB got his, 8 bucks for small ones)

* Look-alike-original mirrors (shop beside LAB) - $20, LAB should be cheaper.

* small foldable square mirror - $45 (HKL)

* Saddlebags $98-190 madman - Pinkphantom.com

* Hazard light less than $10 if u fix&wire urself, $18-20 for mech installation [[ S$15 if Replay does it for you! ]]

* Relocating rear signals to license plate - $10 (planet)

* Relocating rear signals to license plate with bracket - $28 (LAB)

* Rear box $80-330

* Voltage stabiliser - $59-$120 depends

* Rider's ORIGINAL footrest (LAB) - S$18 per side, can be cheaper?

* Stainless steel screws for speedo, and side covers. 6 to change altogether. $1-$1.80 also bought from koon.

* washers to go at 50c each at regina

* Socket for supporting the head light - $15

* Bullet Headlight - $35 (LAB)

* Gear lever with rubber $20 at koon

* Chrome gear and brake levers set - madman

* Stebel Magnum 2 (Silver) w/o installation - $18-$20 (LAB)

* Daiso electric horns (pair) - $45 (planet)

* Phantom TA 200 gearbox - $540 (planet)

* Front fender the "mudflap"- $20 at koon

* Stebel Electric horn with nice hidden installation under front chrome cover- at koon $38

* Re-wrap seat- Starts from about $38 from Eugene saddledry, $25 basic one from Auntie Shop

* Spotlights on crashbar with installation- $35 at koon

* Crashbar- $65 from ah boy DIY

* Anchor and wide type crashbar - madman

* rear no. plate $10..first shop opposite rov..ubi

* 6" Risers - $80 from Auntie Shop in Ubi

 

added few items.

[calico]

yeah had crack according to chong, he got it re-weld for me.. been riding alot.. feels ok to me.. except my bikes been pretty hot.. feel like riding a sports bike lol

[matthias76]

yeah had crack according to chong, he got it re-weld for me.. been riding alot.. feels ok to me.. except my bikes been pretty hot.. feel like riding a sports bike lol

 

you are lucky you sent to ah chong. The shop i went to the last time insisted that I change the block...knn in the end spend $1.2k plus...I angry until now.

[ready2buy]

I went to Unique on 6-Mar for oil change and rear brake pad change. I knew that the clutch plates are worn out too so asked to change them as well. I was told about $90 for clutch plates but when he opened already, he said need to change metal plate also which is $40(4 plates for $10 each). In previous posts, I never saw metal plates price. I myself saw him changing the metal plates but still want to check that the metal plates aren't part of clutch plates or what. I am not aware of that at least!

[ber]

Hi the plates is part of the clutch assembly. The friction is usually sold by itself.and is something like 7 a piece from what I hear from a phantom rider. The metal part price I got no idea the price. The gasket is 7. At least they didn't ask you to change the basket.

 

When it was removed, was it an easy removal? In that nothing dropped, like gears etc when it was removed? I was thinking of doing it myself.

[ready2buy]

Hi the plates is part of the clutch assembly. The friction is usually sold by itself.and is something like 7 a piece from what I hear from a phantom rider. The metal part price I got no idea the price. The gasket is 7. At least they didn't ask you to change the basket.

 

When it was removed, was it an easy removal? In that nothing dropped, like gears etc when it was removed? I was thinking of doing it myself.

Yeah, the change process looked quite simple but you need to first drain out the engine oil to change it.

[incognito6174]

Sounds good, hopefully this battery lasts. Better avoid shops on Lavendar St, their demeanor also is 'Take it or leave it'

[ATTACH=CONFIG]317876[/ATTACH]

 

The price list is from Unique Motorsports. Think on the bright side you are in fact getting a higher spec battery

 

[ATTACH=CONFIG]317877[/ATTACH]

[UshioChan]

Anyone know the size of the phantom headlight bulb ??

[matthias76]

Anyone know the size of the phantom headlight bulb ??

 

H6M, if tats what you are asking.

[kzone]

hi guys, my front fork leaking oil. need to change the whole fork or can just top oil & re seal?

[sawfly]

hi guys, my front fork leaking oil. need to change the whole fork or can just top oil & re seal?

 

usually ppl willl change fork seals first and try to find the source of leak. may not need to change entire fork, could be just a bug that is interfering with the seal. changing fork is extreme when you cant find the source of leak or the pitting due to corrosion is that far down the tube.