[Group] Singapore BAJAJ Team (SBT)

[Brandonwang]

Anybody know how to reduce vibration on the handle bar? Been shaking quite badly this 2 days reach destination with numb palms

[m0bIlEnErD]

Anybody know how to reduce vibration on the handle bar? Been shaking quite badly this 2 days reach destination with numb palms

 

wear gloves. it helps.

vibrations could also mean you could be over-revving your engine.

[atipo]

his gf parent release his coming wedding proposal list ..... kkkkakakaakaa

 

like me .. the most 2 important news to wait ... the approval dates on my engagement and also my official wedding dates!! .... new life and new responsibilties .... hehehehehee

 

Spoken like a true married man.............. Eh u're married ah?Kkekekekekekek:)

[alvinyansg]

Anybody know how to reduce vibration on the handle bar? Been shaking quite badly this 2 days reach destination with numb palms

 

since the vibrations are from your handlebar...

just remove your handlebar...

then no more vibrations...

haha...

[Brandonwang]

wear gloves. it helps.

vibrations could also mean you could be over-revving your engine.

 

I only ride 85 - 95 cannot be over revving the engine, was wondering if i tighten the middle nuts will it help.

Do you have the same problem?

[atipo]

Anybody know how to reduce vibration on the handle bar? Been shaking quite badly this 2 days reach destination with numb palms

 

No quick cure for this issue bro,Need to check 1) Steering cone bearings ( wear/tear) 2) Tyres pressure or tyre itself ( lumpy or distorted/ underpressure)3) Rim bearings ( wear / tear) 4) Fork alingments. All play a factor. But wearing gloves do help + a heavier end balancer. Worst case scenario, buy new bike, no vibrations:)

[Fredd]

middle nuts

 

I only ride 85 - 95 cannot be over revving the engine, was wondering if i tighten the middle nuts will it help.

Do you have the same problem?

[atipo]

since the vibrations are from your handlebar...

just remove your handlebar...

then no more vibrations...

haha...

 

i loike

[atipo]

middle nuts

 

Corrupt minds:)

[m0bIlEnErD]

I only ride 85 - 95 cannot be over revving the engine, was wondering if i tighten the middle nuts will it help.

Do you have the same problem?

 

My last P200 only had 3000 kms on it. So no vibration problems.

Only very minimal vibration on the foot pegs.

[Brandonwang]

No quick cure for this issue bro,Need to check 1) Steering cone bearings ( wear/tear) 2) Tyres pressure or tyre itself ( lumpy or distorted/ underpressure)3) Rim bearings ( wear / tear) 4) Fork alingments. All play a factor. But wearing gloves do help + a heavier end balancer. Worst case scenario, buy new bike, no vibrations:)

 

I like the idea of getting a new bike LOL. But those problem that u mention, i think steering cone bearing is the issue, i'm gonna get durian gloves for riding heheehehehe

[Brandonwang]

middle nuts

 

I love nuts

 

i loike

 

Super irritating

 

Corrupt minds:)

 

:):)

 

My last P200 only had 3000 kms on it. So no vibration problems.

Only very minimal vibration on the foot pegs.

 

Mine is running at 59K and vibration starts 2 days back i think its time to change the whole bike kekekekeke

[revhappy]

I only ride 85 - 95 cannot be over revving the engine, was wondering if i tighten the middle nuts will it help.

Do you have the same problem?

 

Could be engine oil also. Check Oil level and how old it is?

[atipo]

[quote=Brandonwang;

Mine is running at 59K and vibration starts 2 days back i think its time to change the whole bike kekekekeke

 

Maybe can go for check up @UM.

[speedaddict]

My tyre just gave way on expressway. Wobbling all the way home. Then wobble all the way to tampines workshop to change now.. Zzz was just about to go inspection..

[Brandonwang]

Could be engine oil also. Check Oil level and how old it is?

 

Just change 2 days ago

 

Maybe can go for check up @UM.

 

Just been there 2 days ago will find time to go back soon, sian waste $ again.

 

My tyre just gave way on expressway. Wobbling all the way home. Then wobble all the way to tampines workshop to change now.. Zzz was just about to go inspection..

 

Y u always so drama, be careful ok :)

[mjbs64]

@Brandonwang ..... first thing first

 

1: end weights damper: tightened your handle end weights!!! .... btw what type of end weights you used? .. stock is good enough since the handguards are not here yet!! ..

 

2: wheel bearing: put on main stand ... grab tight the front fork with one hand while the other hand try to pull up and down the front wheel .. if you hear knocking sound or your wheel can move up and down while pulling .. meaning your wheel bearing need to change. Btw .. since your milage have almost reached 60k .. wise to change lah if you have not done so .. .

"

Wheel bearings usually last quite a while, perhaps 15,000 to 30,000 miles. If you feel any play in the bearings replace them. If the wheel hub feels very hot to the touch, check to see if the brakes are dragging. If the brakes are not dragging, replace the bearings because there has been a lubrication failure. The bearings have overheated and are ruined. Likewise, if you have the axle out for some reason, like a tire change, and you notice it is discolored, as if it had been heated up with a torch, replace the bearings and the axle too. If you are going on a long trip and can't remember when you last replaced the wheel bearings, replace the bearings. If in doubt, replace the bearings. You only have two wheels. If one locks up at speed, you will be in BIG trouble! " dan motorcycle

 

3: wheel alighnment : main stand .. rotate the front wheel and observe the wheel rotates for any wobbling.

 

4: fork oil: tie a cable tight around the fork. Sit and push the bike forward and applied the front brake.. check the level of the cable tie if both balance or not. ... btw top up the fork oil if have not done so

 

5: cone bearing: go UM to check

 

6: others: go Um to check

 

 

my share only ... cheers!

Edited April 26, 2011 by mjbs64

[mjbs64]

My tyre just gave way on expressway. Wobbling all the way home. Then wobble all the way to tampines workshop to change now.. Zzz was just about to go inspection..

 

tyre gaveway?????? .....

 

can share more how it happened and actually what happened ?????????? ....

[Brandonwang]

@Brandonwang ..... first thing first

 

1: end weights damper: tightened your handle end weights!!! .... btw what type of end weights you used? .. stock is good enough since the handguards are not here yet!! ..

 

2: wheel bearing: put on main stand ... grab tight the front fork with one hand while the other hand try to pull up and down the front wheel .. if you hear knocking sound or your wheel can move up and down while pulling .. meaning your wheel bearing ned to change.

 

3: wheel alighnment : main stand .. rotate the front wheel and observe the wheel rotates for ant wobbling.

 

4: fork oil: tie a cable tight around the fork. Sit and push the bike forward and applied the front brake.. check the level of the cable tie if both balance or not. ... btw top up the fork oil if have not done so

 

5: cone bearing: go UM to check

 

6: others: go Um to check

 

 

my share only ... cheers!

 

MjMjMjMjMj :):)

 

1. Motovation balancer good enough will tighten after the rain.

 

2. Just change 2 days ago so cfm tight until cannot tight. :)

 

3. Check by ah tek during servicing so no issue

 

4. Will try that after the rain

 

5. Its time to change $62 exclude labour

 

6. Will go down again soon.

 

Thank you you you you you you. Teh terik :):)

[avilu]

Anyone recommends a shop where I can buy safety gears? I remember O'ren had posted the link somewhere but guess I lost it.

Edited April 26, 2011 by avilu

[mjbs64]

Anyone recommends a shop where I can buy safety gears? I remember O'ren has posted the link somewhere but guess I lost it.

 

regina, chiap lee, cheong aik, motoworld, all near ahboy there...

rain armour jurong west ave 1 ...

 

please don't ask which one cheaper ... you need to try for individual needs ...

 

happy hunting ..... hehehehee

[mjbs64]

Gaban asked me to post since he is out .....

 

JB Bike Wash or Makan or Top up Tonite!!

 

Anyone going in tonite ... tag him along do msg him.

 

 

anyway I'm not going .... hehehhee

[mjbs64]

Bajaj Team Weekly Outing (27 Apr 2011)

 

Venue : KTM

[ATTACH=CONFIG]201996[/ATTACH][

Time : 2130 till 2330

 

1) Fredd

2) YenYu

3) O'Ren

4) Fiddy (pending.. Cadets have navigation courseee.. )

5) mjbs64

6) mobilenerd (tentatively coming)

 

whomever arrives aft 11 must blanja teh tarik!!!

 

To add on ... parking behind at the food canteen carpark at the red marker on the map.

 

http://www.onemap.sg/?SearchVal=KEPPEL%20ROAD&LW:Y&N1kg:zd@JbaYJ_h,JbhJI_q,I,qacqqabY,JY/zd@JbfbR_R,JbhJq_R,I,qacqqabY,JY/zd@Jbfcc_R,JbhJJ_f,I,qacqqabY,JY&wO5d:Jbqfh_f,Jbqfb_a,JRqYc_a,JbfRq_f,c

 

[Fredd]

Bajaj Team Weekly Outing (27 Apr 2011)

 

Venue : KTM

[ATTACH=CONFIG]201996[/ATTACH][

Time : 2130 till 2330

 

1) Fredd

2) YenYu

3) O'Ren

4) Fiddy (pending.. Cadets have navigation courseee.. )

5) mjbs64

6) mobilenerd (tentatively coming)

7) atipo

 

whomever arrives aft 11 must blanja teh tarik!!!

 

To add on ... parking behind at the food canteen carpark at the red marker on the map.

 

http://www.onemap.sg/?SearchVal=KEPPEL%20ROAD&LW:Y&N1kg:zd@JbaYJ_h,JbhJI_q,I,qacqqabY,JY/zd@JbfbR_R,JbhJq_R,I,qacqqabY,JY/zd@Jbfcc_R,JbhJJ_f,I,qacqqabY,JY&wO5d:Jbqfh_f,Jbqfb_a,JRqYc_a,JbfRq_f,c

 

[avilu]

regina, chiap lee, cheong aik, motoworld, all near ahboy there...

rain armour jurong west ave 1 ...

 

please don't ask which one cheaper ... you need to try for individual needs ...

 

happy hunting ..... hehehehee

 

Thanks a ton.. !!! Guess I have learnt from one accident. :-)