CBR150R Riders, Join us now!

[cyrusv]

Thks for ur reply bro.

Bro juz wondering, what does the fag bearings include?and hw much and hw much to install them and do an engine overhaul(as in juz change the conrod,conrod piston bearing,piston n piston ring?) at AGL? Thx!

 

Bearings from FAG-Germany would cost you around SGD 90, there is also a special size bearing from NTN-Japan for your crankcase that would cost you another SGD 40. All this bearings are made from either Germany, Korea or Japan and not the cheap products from China and Taiwan.

Conrod for CBR-150R is not sold separately it comes in 1 set that would cost you around SGD300 if I am not wrong. Piston and piston ring would be around SGD100(Original and not local)

 

there can be different reasons why the battery is flat/low.

if it's purely because the battery is reaching end of lifespan, then fair and square.

but if it's because the charging system isn't working well, then this new battery is just going to end up dead sooner or later. i.e. what you've got is only a temporary fix.

so please make sure that the shop does the necessary checks on the charging system as well k.

 

IMHO, it seems a bit coincidental that the battery has to spoil along when you encountered the engine dying off issue.

and it seems that even after the new battery change, the engine dying issue is still not completely resolved.

leads me to question if the battery is the really the cause/part of the cause.

 

This is most probably due to your carb. CBR 150R carb has a rubber diaphragm compared to other model of bikes, try getting your mech to check the rubber diaphragm, or the needles in the carb. I personally experience similar problem but after a general service where my carb is cleaned it stop giving me the problems

 

 

nice. didn't know that Hou Heng has got stocks available for that many parts for our bike.

some of the stuff like rubber bushing for rear wheel hub were not available like 2-3yrs back.

I bought some parts myself. Would be glad to get the stock parts for you……

Edited December 22, 2011 by cyrusv

[Puteraboncet]

Theory should be more than 40km/l. haha.

 

What's your fuel consumption?

 

 

 

In the first place.. how to calculate fuel consumption ah ? hahaha

[xbfish]

Anybody have an English Manual for 2011 CBR150Ri? Thanks in advance.

 

I got english owner manual for CBR150i. Got service manual for cbr250 which u can slightly refer to. Can pm me your email and i'll send to you.

[xbfish]

In the first place.. how to calculate fuel consumption ah ? hahaha

 

Total distance travelled (km) / [ Size of Petrol tank (litres) - Amount of petrol pumped (litres) ]

 

A math equation

[x3mtoxic]

I got english owner manual for CBR150i. Got service manual for cbr250 which u can slightly refer to. Can pm me your email and i'll send to you.

 

Cool! PM sent. Thanks.

[wenn]

I got english owner manual for CBR150i. Got service manual for cbr250 which u can slightly refer to. Can pm me your email and i'll send to you.

 

Me also want...PM you liao..

[Puteraboncet]

Total distance travelled (km) / [ Size of Petrol tank (litres) - Amount of petrol pumped (litres) ]

 

A math equation

 

ALAMAK ! A Maths equation ehh ?? hahahaha

[xbfish]

Cool! PM sent. Thanks.

 

Oh ****! I got it wrongly. Actually I only have CBR250R owner manual in English, CBR150i and CBR250i service manual in Thai.

 

The service manual exceeds 25Mb email attachment and I can't send through. Do you have msn?

 

Anyway, I send you the owner manual of CBR250R in English liao.

 

Me also want...PM you liao..

 

Already sent you through MSN before liao. haha.

[xbfish]

ALAMAK ! A Maths equation ehh ?? hahahaha

 

Not A-math lah. haha

 

Is math equation. haha.

[xbfish]

For those interesting in getting white bulb to fix on their motorcycles, can see my blog post @ http://xbfish.com/2011/12/21/hs-white-bulb-for-motorcycles/

 

The white bulb won't melt your socket. You can get it from @limbat

 

[d0n]

I bought some parts myself. Would be glad to get the stock parts for you……

 

nice.

the last time i brought my own clutch plates when doing clutch plate change at hou heng, i was charged a little more for bringing my own parts.

 

For those interesting in getting white bulb to fix on their motorcycles, can see my blog post @ http://xbfish.com/2011/12/21/hs-white-bulb-for-motorcycles/

 

The white bulb won't melt your socket. You can get it from @limbat

 

 

this bulb tried and tested~

no melting!

[Puteraboncet]

For those interesting in getting white bulb to fix on their motorcycles, can see my blog post @ http://xbfish.com/2011/12/21/hs-white-bulb-for-motorcycles/

 

The white bulb won't melt your socket. You can get it from @limbat

 

 

 

Better visibility ? btw how much including installation ? where can I get it fix ? hahaha

[xXxRatedxXx]

For those interesting in getting white bulb to fix on their motorcycles, can see my blog post @ http://xbfish.com/2011/12/21/hs-white-bulb-for-motorcycles/

 

The white bulb won't melt your socket. You can get it from @limbat

 

 

25W still ok... that time i used 35W.. melted both my sockets. ****ing China bulbs

[Puteraboncet]

guys, our sprocket front and back stock setting how many teeth ? I need to change my sprocket already lei . any recommend setting for me ? I'm big size (fat) + my pillion also big (fat ) so what best setting ? i want pick up more abit )

[x3mtoxic]

Oh ****! I got it wrongly. Actually I only have CBR250R owner manual in English, CBR150i and CBR250i service manual in Thai.

 

The service manual exceeds 25Mb email attachment and I can't send through. Do you have msn?

 

".............

S

I dont have msn...... Thanks anyway.

[x3mtoxic]

Oh ****! I got it wrongly. Actually I only have CBR250R owner manual in English, CBR150i and CBR250i service manual in Thai.

 

The service manual exceeds 25Mb email attachment and I can't send through. Do you have msn?

 

".............

S

I dont have msn...... Thanks anyway.

[xbfish]

25W still ok... that time i used 35W.. melted both my sockets. ****ing China bulbs

 

Yeah. Those china bulbs melted my nsr sockets last time. sibei cui...

 

guys, our sprocket front and back stock setting how many teeth ? I need to change my sprocket already lei . any recommend setting for me ? I'm big size (fat) + my pillion also big (fat ) so what best setting ? i want pick up more abit )

 

The stock setting for sprockets are as follows:

 

Rear sprocket Parts Number: 41200-KPP-900 , 44T

 

Front sprocket Parts Number: 23801-KBP-900 , 15T

 

Hope this helps

[xbfish]

S

I dont have msn...... Thanks anyway.

 

I send to your yahoo mail liao.

[Puteraboncet]

Yeah. Those china bulbs melted my nsr sockets last time. sibei cui...

 

 

 

The stock setting for sprockets are as follows:

 

Rear sprocket Parts Number: 41200-KPP-900 , 44T

 

Front sprocket Parts Number: 23801-KBP-900 , 15T

 

Hope this helps

 

 

Thanks ! but do u guy know any good setting for pple like me ? those big size cause my pick up not that good lah, smaller front + bigger rear shall do the trick ?

[xbfish]

Thanks ! but do u guy know any good setting for pple like me ? those big size cause my pick up not that good lah, smaller front + bigger rear shall do the trick ?

 

I am not very sure about sprocket settings because I've been using stock setting all the way. haha.

[TAJ]

hello...would like to enquire regards to coolant issue on my cbr..yest just fill up coolant and to when im riding the temp gauge went to almost half..any idea?prev have not been topping up coolant for the past few months..

[MywishxD]

hello...would like to enquire regards to coolant issue on my cbr..yest just fill up coolant and to when im riding the temp gauge went to almost half..any idea?prev have not been topping up coolant for the past few months..

i guess half is still conmon?

[xXxRatedxXx]

hello...would like to enquire regards to coolant issue on my cbr..yest just fill up coolant and to when im riding the temp gauge went to almost half..any idea?prev have not been topping up coolant for the past few months..

 

Then go and check your coolant la... since you say never top up.

[xXxRatedxXx]

hello...would like to enquire regards to coolant issue on my cbr..yest just fill up coolant and to when im riding the temp gauge went to almost half..any idea?prev have not been topping up coolant for the past few months..

 

Then go and check your coolant la... since you say never top up.

[quadro]

Hi,

 

Got my wielding done at 27 Jurong Port road 01-19. They need like half to one full day (park morning, collect evening) to get the job done depending on condition. The price is reasonable than compared to my case - to get a $200 replacement for the hose.

 

pls share where u managed to get the welding/patching done~

it seems like the extractor (the black color portion of the exhaust pipe that runs from underneath engine to passenger footrest area) keeps getting rusty.

i bought an exhaust wrap to wrap up the portion to make it look more decent. but i know that his probably doesn't reduce the fact that it will still get rusty underneath.

maybe one day my extractor will break into 2 also

 

 

 

nice~