[Group] Singapore BAJAJ Team (SBT)

[Lucky21]

use chex..good for touring

 

The Chex EO is cheap and good. Been using it for a period of time and really worth the money.

[SC Gaban]

Was riding my pulsar180 2 werk dis morning. the vibration was so bad dat after parking my bike, my balls turned numb. after a few mins, the blood returns n circulates, den i was relieved. hehe.

 

will be dropping by UM after firday prayer to rectify the wiring problem.

no light on dashboard, no front light, no electric start, no brake light. turn handlebar - lights gone.

[revhappy]

Under Used Bike Section. Coe till 2017. So tempting. Save me hassle of respraying.

 

Yeah looks awesome. Could be Fredd's old bike

 

http://www.singaporebikes.com/forums/showthread.php/324062-Bajaj-Pulsar-180-UG3-FBB-Plate-for-Sale

Edited May 27, 2011 by revhappy

[revhappy]

use chex..good for touring

 

Yupp! I vouch for it:thumb: Its a 50W oil so its thicker and will be more smoother on gear shifts and engine noise and at very high temperatures better protection. But downside of thicker oil is that because its thicker engine's pickup will reduce by a bit.

 

But why only Chex when there are so many branded 50W oil?

Ans: The cost:angel: its costs 14$-16$ and is as good as any fully synthetic 50 weight oil.

[Seif]

DIY Session

 

Date: 28th may 2011(Sat)

Location: Blk 541A Jelapang Road(MSCP),Deck 5A

Time: 2pm-5pm

Things to bring: Tool Kit,coils etc

 

*Might want to bring water to drink*

 

Interested please leave your name below.

If nobody interested then will be doing my own wiring under my blk.

 

 

Name

 

1. Fiddyyyy! Gonna squeeze all the knowledge from you!

2. dejaxx

3.

4.

5.

[Seif]

@alvinyansg thanks for reserving time for DIY!

[Seif]

i THINK i've seen that yellow pulsar during my last servicing @ UM.... had a chat with the owner...

[mfk74]

DIY Session

 

Date: 28th may 2011(Sat)

Location: Blk 541A Jelapang Road(MSCP),Deck 5A

Time: 2pm-5pm

Things to bring: Tool Kit,coils etc

 

*Might want to bring water to drink*

 

Interested please leave your name below.

If nobody interested then will be doing my own wiring under my blk.

 

 

Name

 

1. Fiddyyyy! Gonna squeeze all the knowledge from you!

2. dejaxx

3. mfk74 (tentatively yes)

4.

5.

[Fredd]

http://tapatalk.com/mu/dcff0221-17ec-bf53.jpghttp://tapatalk.com/mu/dcff0227-1830-46a6.jpghttp://tapatalk.com/mu/dcff024e-1845-ca7f.jpg

 

My beloved ex-pulsar

[m0bIlEnErD]

Fredd, this one is UG3. Not P200.

Although I prefer P200, but this one is YELLOW!!!

[RideHard]

bro, i frequent FZ16 thread often... havin myself browsing here occasionally, I personally appreciate e knowledge n experiences u've impart wif fellow riders! Cheers!

 

hmmm .. you can try changing other EO to have a feel if it's the same feeling you encountered. Every bike has it's own charactors and every rider has their own feel of their bike ...

 

It's also how the way we ride our bike too to have the bike to its top performance ...

 

eg only : riding slow does not mean it's good for the engine and whacking the bike also does not mean it's harm the engine too.

It's all about the engine itself from the very beginning ...

 

 

"Any rebuilt or new engine has to go through a break in process. Each piece of moving metal must get to know and fit with the piece of metal it is moving against. Usually, the manufacturers put a sticker on the speedometer or tachometer telling you to take it easy for 600 miles or so. Your buddy says "If you want to run it hard, break it in hard." As you might expect, the truth is not on the right hand or the left but, in the center.

 

The problem is this. All this rubbing produces heat, which can cause oil to fail, which can cause a piston to seize to a cylinder wall. On the other hand, if there is not enough rubbing, the piston rings will not seat right with the cylinder walls. If this happens the engine will not reach it's full power potential. If the only new parts are piston and rings, as in an engine rebuild, we only have to worry about heat build up from the new parts. If the entire engine is new, the heat built up is even greater, because all the parts are new.

 

Yes, it is true that we have much better machining and quality control on new motorcycle engines, then we did in the past but, moving parts still have to wear in. If you have better, harder metal, it will take longer then if you have poorer, softer metal. Years ago I decided to bore my BMW motorcycle to the first oversize. After a hundred miles of break-in I started to ride normally, which is to say FAST ! Well, the bike just was not running right. I re-jetted the carb and it started to run OK. Another hundred miles passed and I had to rejet again. This went on for over one thousand miles. After the last re-jetting I realized I had just put the stock jets back in ! It took better then 1100 miles for those rings to break-in. The steel used in BMW motorcycles is very hard !

 

On one hand, if you run the bike too easy, you run the risk of the cylinder walls glazing over and then, maybe, never seating properly. On the other hand, if you run the bike too hard, you run the risk of engine seizure. I suspect, that even if you do glaze the cylinder walls over, if your run the engine hard enough and long enough, the rings will seat. However, this may take a thousand miles, or more, to do.

 

So what's a biker to do ? Well, a compromise is in order. This is what I do with a freshly rebuilt engine. It will work on new engines too. On a straight, deserted road, I put the bike in second or third gear and accelerate with wide open throttle to about one or two thousand RPM BELOW red line. I then shut the throttle and coast down, in gear, to two thousand RPM or so. I then do it again. I do this about ten times. Then I ride around for a while at an easy pace. I do this several times, if possible. This seats the rings without overheating the engine." .. (dan's motorcycle)

[Fredd]

come join us during our weekly meetups..we will poison u wif more knowledge n other stuff..hahaha. wad bike u ridin? fz16?

 

bro, i frequent FZ16 thread often... havin myself browsing here occasionally, I personally appreciate e knowledge n experiences u've impart wif fellow riders! Cheers!

[revhappy]

Fredd, this one is UG3. Not P200.

Although I prefer P200, but this one is YELLOW!!!

 

Why do you like yellow so much? Is it your favorite color or only for Pulsar?

 

My favorite color is orange followed by red for cars or bikes. I somehow dont like black, haha

[m0bIlEnErD]

My favourite colors are yellow and purple.

No real preference for car colors although I have had a few chilli red cars.

 

Just saw an MP3 125cc for sale at Used Bikes for $8500. hmmm out of my budget.

[alvinyansg]

bro, i frequent FZ16 thread often... havin myself browsing here occasionally, I personally appreciate e knowledge n experiences u've impart wif fellow riders! Cheers!

 

come down for meet ups and learn of more poison...

can ask @YenYu...

haha...

 

protec coil...

tdk stab...

air filter not out yet...

Edited May 27, 2011 by alvinyansg

[mjbs64]

bro, i frequent FZ16 thread often... havin myself browsing here occasionally, I personally appreciate e knowledge n experiences u've impart wif fellow riders! Cheers!

 

Appreciate bro .. just sharing since we are bikers after all !! .. kakakakaa

 

join us lah ... the more the merrier who cares which 2 wheels we ride .. most important is FRIENDSHIP BONDING!! .. kekekeke

 

CHEERS!

[mjbs64]

spam alert! ...

 

change my avatar ... that's my name in japanese

 

shi fu a ra = jaffar

 

nice name right? ... kekekekeee

 

here's the link .. http://apps.facebook.com/nameinjap/?t=home

 

 

eg : revhappy = re wa a ya

 

http://www.singaporebikes.com/forums/attachment.php?attachmentid=205688&d=1306482789

 

 

cheers!

Edited May 27, 2011 by mjbs64

[revhappy]

Anyone looking for Rizoma lookalike Handle bar grips

 

http://www.singaporebikes.com/forums/showthread.php/324115-Selling-off-bike-items!

 

This one suits our pulsar

[speedaddict]

wanna btmo tmrw to jb? or just night riding?

[alvinyansg]

autobacs promo for broquet...

in tank 8=$140...in tank 5=$95

[speedaddict]

AGL or Pandan City tonight anyone? Me and Gaban might go..

[alvinyansg]

just now at a traffic junction saw a pulsar rider on the opp direction staring at my bike when i rode pass..

seems to be staring at my HG...

[alvinyansg]

AGL or Pandan City tonight anyone? Me and Gaban might go..

 

need to pump...

but 2ml got an early morning...

[mfk74]

just now at a traffic junction saw a pulsar rider on the opp direction staring at my bike when i rode pass..

seems to be staring at my HG...

 

hahaha..me too..some pulsar rider look @ my sprocket !!!

[alvinyansg]

hahaha..me too..some pulsar rider look @ my sprocket !!!

 

if not for different direction and i heading to meet my friend i would have stopped,U turn and pass him the leaflet...