SBF Silverwings / HOM Cafe 2012

[confusehaha]

any one here got reali bad f/c before.just done my first tank avg 17.5km/l.sounds reali bad.

think i reali b tearing apart again tomorrow.

 

If urs is a jdm model. 01 to 05 model. It will be a norm to achieve fc of 17 to 19km/l.

[Fusionjaz]

Home sweet home.

Someone in our group experience jb gang harassment

[Jupiter9002]

Home sweet home.

Someone in our group experience jb gang harassment

Someone ? I thought travel in group ?

[scoobydoo]

jb gang harassment

wah...

 

hope everyone got out safely

[Atlantic 200]

Who.... Me & Kelvin went for bike washed, home sweet home.

[SW9000]

Gang harassment?

Not me.

[jsilverwing]

infront of me,too late didnt see the plate number and they go off when reaching.

Edited October 16, 2013 by jsilverwing

[Fusionjaz]

This shall be "the story" to be told tomorrow meet up.

There is always some experience to be learn from each ride. That is the joy of riding.

[Nighthawk_250]

any one here got reali bad f/c before.just done my first tank avg 17.5km/l.sounds reali bad.

think i reali b tearing apart again tomorrow.

 

Just contribute some experieience I had with my JDM

should be same year as urs.

 

17km/l since the day i bought it

Ive changed to 26g Dr pulley roller and a new belt months back.

(rpm drop 500, Previously 5.5k rpm for 90km/h, Now its 5k rpm for 90km/h)

 

No fuel saving for me with dr pulley or the original 28g green roller

Infact I enjoy the 28gm roller more for the mid range speed...it pulls better.

 

My last 2 full tank did 15.5 to 16 km / L only hahaha got a rude shock.

 

Waiting for the torque spring to come and then I'll likely change the variator, clutch and clutch bell etc.

 

I also open the lid to check the air/vaccum valve to look see...one of them is open to the max (end)

whilst the other is about 2+ turn...duno why so much diff..

[HelmetBOX1605198525]

Gang harassment?

Not me.

 

you will will have gang harassment? only sexual harssement.. haha..

[echris108]

i think mine is the jdm cuz got e t button.

it was 2/1.8 screw in.i did everything in then 1.8 out for both.

now my idle is only 1.1 k even when warming up.just need to do my balance at a later time once i sort out wat i need.

in equal more air or fuel?

[scoobydoo]

I also open the lid to check the air/vaccum valve to look see...one of them is open to the max (end)

whilst the other is about 2+ turn...duno why so much diff..

i think mine is the jdm cuz got e t button.

it was 2/1.8 screw in.i did everything in then 1.8 out for both.

now my idle is only 1.1 k even when warming up.just need to do my balance at a later time once i sort out wat i need.

in equal more air or fuel?

time to do airscrew sync.

note that vacuum levels may not be synchronized when both screws are at same "turns". you'll need vacuum gauges or tools like carbtune to measure/level the settings.

check this out... Air Screw Synchronisation

[scoobydoo]

not riding today cos headlight out of order... failed self inspection few days back

checked liow, bulb and fuse both ok. need to bring down sai-tow to check wiring ... grrrrrr

 

 

tonight meetup at King Albert McD confirm bo?

[armani123sg]

not riding today cos headlight out of order... failed self inspection few days back

checked liow, bulb and fuse both ok. need to bring down sai-tow to check wiring ... grrrrrr

 

 

tonight meetup at King Albert McD confirm bo?

 

Try spamming wd40 into left hand switch. Look for any gap n really spam wd40 inside until dripping. Worked on all my bikes. Haha

[Nighthawk_250]

time to do airscrew sync.

note that vacuum levels may not be synchronized when both screws are at same "turns". you'll need vacuum gauges or tools like carbtune to measure/level the settings.

check this out... Air Screw Synchronisation

 

thanks Scooby,

 

do u know where to buy the vaccum guage locally ?

Saw on ebay about S$65/pair to door but must wait.

 

Suppose to tune it at Ac motor..but curious to DIY and see the results with different turn.

[SW9000]

Normal Air screw is 2 turns out.

Don't touch 1 side (use a reference) and only adjust the other to balance.

Adjust (for both balance and RPM) only after the bike has warmed up significantly. Best after a ride.

 

As for RPM, there are 2 points the bike would have stable RPM.

1.1k or 1.3k or around there. * Original bike normally comes with 1.3k+/-.

Place you hand at the handle grip and also watch the front shield for vibration.

The least vibration the better, yah?

[scoobydoo]

thanks Scooby,

 

do u know where to buy the vaccum guage locally ?

Saw on ebay about S$65/pair to door but must wait.

 

Suppose to tune it at Ac motor..but curious to DIY and see the results with different turn.

i also can't find from sg websites so bought from amazon in the end. if got pp keen to DIY, i dun mind organising a DIY session at my place MSCP one of the weekends. but 1st gotta dig it out from store and check if the gauges are still working or not

 

if you dun mind paying more, can consider liaise with seller and ask for overnight express air freight... you'll get it in a matter of days

[scoobydoo]

Try spamming wd40 into left hand switch. Look for any gap n really spam wd40 inside until dripping. Worked on all my bikes. Haha

my phantom's chrome parts/forks became rusty after foolishly using as cleaning/lubrication agent. paid for the lesson and stopped using it on bikes ever since

 

some info about WD40... many yeas and nays

from manufacturer:

http://www.wd40.com.au/wd40/faq.php

http://wd40.com/files/pdf/wd_40tec16952473.pdf

from users:

http://lifehacker.com/5891936/when-should-i-not-use-wd+40

http://www.naturalhandyman.com/iip/infxtra/infwd40.html

http://sg.answers.yahoo.com/question/index?qid=20070812190359AAM7ScD

Edited October 17, 2013 by scoobydoo

[jsilverwing]

not riding today cos headlight out of order... failed self inspection few days back

checked liow, bulb and fuse both ok. need to bring down sai-tow to check wiring ... grrrrrr

 

 

tonight meetup at King Albert McD confirm bo?

 

maybe relay headlight fail and who going down,k A M,can see u.

[echris108]

jdm model got the t button n the exhaust valve thing.

anyone here got bypass the valve and set to full open all the time?

tonite got meet up?

[echris108]

jdm model got the t button n the exhaust valve thing.

anyone here got bypass the valve and set to full open all the time?

tonite got meet up?

[scoobydoo]

tonite got meet up?

tonight meetup at King Albert McDOnald's... 7pm onwards ba

http://gothere.sg/maps#q:king%20albert%20park%20mcdonald's

[Fusionjaz]

i'll be there.

See ya

[echris108]

hi,as a first timer.how would i recogise any of u?

[armani123sg]

my phantom's chrome parts/forks became rusty after foolishly using as cleaning/lubrication agent. paid for the lesson and stopped using it on bikes ever since

 

some info about WD40... many yeas and nays

from manufacturer:

http://www.wd40.com.au/wd40/faq.php

http://wd40.com/files/pdf/wd_40tec16952473.pdf

from users:

http://lifehacker.com/5891936/when-should-i-not-use-wd+40

http://www.naturalhandyman.com/iip/infxtra/infwd40.html

http://sg.answers.yahoo.com/question/index?qid=20070812190359AAM7ScD

 

But sw no chrome parts ma? And my fren whack wd40 ALL over his st11. Damn swee. 3 years already. Still damn swee. Haha. But if u think wd40 cant, then maybe you can use other types of contact cleaners/penetrants to spray? Those which are proven to not cause rust?