[Discussion] Super Four General Enquiry Thread

[pyro13]

I'm in urgent need to replace my rear wheel bearings and dust cover. Anyone have any idea which shop opens today or tomorrow?

 

Fazli, at lv thread, they were saying abt a shop tat is open on cny.. Try asking ter?

[pyro13]

if tht so, i'm not going to touch it anyway. thnks ya. r u using knn airfilter??? can it wash with water or the treatment itself??

 

Im using knn filter.. D shop normally handles

The servicing for me.. But they wash wit water.. After which, they blast the whole thing wit air and then them treat wit d soution

[pyro13]

nope...i saw my fren using...he just lower the fork till its enough for the handlebars to clip on..i feel the position more 'fierce' le..heheh..its like u can hug the tank

 

Isit?? Doesnt the front tyre get used up pretty fast tat way?? My frens told me to lower front fork and all... But my mech told me that the front fork seal will leak faster and front tyre wears put fasyer

[Fazli]

Thanks Pyro~!

[LoudnessFz]

Isit?? Doesnt the front tyre get used up pretty fast tat way?? My frens told me to lower front fork and all... But my mech told me that the front fork seal will leak faster and front tyre wears put fasyer

 

hmm....not sure about that..my fren's using it..seems ok..he's been using it for almost 2 years

[pyro13]

Isit?? Possible to post some pics ere??

[LoudnessFz]

umm...see if i can take pic of his bike without him notice..heheh..he's not that close fren of mine so yea..dont wanna him think i copycat or something

[Fazli]

Drop fork will not wear out your tyres faster. It actually alters your bikes geometry. Even changes of 1-2mm in the geometry affects the handling response of the bike. When you drop your fork, your wheelbase actually will shorten. This will improve the cornering response as in when you flick your bike into the corner it is very nimble. But, a very short wheelbase will affect your high speed straight line stability. I ever tried before and it starts to wobble at 100km/h. Reset back the fork height and everything is back to normal.

[Tommyquek]

Hey fellow s4 bros, recently i just found out that it is very difficult to change gear. When i kick down or up, nth seems to happen its just like *when you are in gear 1 and you kick the lever down* feeling. Does anyone knows what is happening to my bike?

[pyro13]

Hey fellow s4 bros, recently i just found out that it is very difficult to change gear. When i kick down or up, nth seems to happen its just like *when you are in gear 1 and you kick the lever down* feeling. Does anyone knows what is happening to my bike?

 

Do check ur clutch cable

[Ah Pek]

Hey fellow s4 bros, recently i just found out that it is very difficult to change gear. When i kick down or up, nth seems to happen its just like *when you are in gear 1 and you kick the lever down* feeling. Does anyone knows what is happening to my bike?

 

Yah...Pryro13 is right..your "biting point" that is and also...check ur chain tension for xtreme looseness.

[Fazli]

Adjust by your cable tension adjusters on your lever. If that doesn't work, you need to adjust it on the right hand side of your engine for the tension.

[Tommyquek]

Do check ur clutch cable

 

okay thanks

[Tommyquek]

Yah...Pryro13 is right..your "biting point" that is and also...check ur chain tension for xtreme looseness.

 

chain also will affect gear changing?

[Tommyquek]

Adjust by your cable tension adjusters on your lever. If that doesn't work, you need to adjust it on the right hand side of your engine for the tension.

 

I've adjusted the one on the lever alr. later going to try the engine side. thanks alot guys. shall update you guys agn.

[Fazli]

Yes, cos when your chain is too slack, gear not able to engage properly due to the alignment of your splined drive shaft and gear cogs.

[Nasser]

i heard flower disk n small led signal light not approve wen going inspection.. izzit true..?

[ZeekyZacky]

Hmm fr me, i pass the inspectionn with small led and flower disc...

[lauhs8]

Mileage LED screen blacken in some portion

 

1. Anyone know best place to change this? In term of price and workmanship.

2. Do i have to change all 3 as a unit i.e the Speedo,Tacho & mileage reading LED or just the mileage reading LED?

 

Thanks in advance.

New S4 rider

[lauhs8]

Knowing the correct spec of the Bike

 

Told by previous owner this S4 is VTech1 but when i see the log card it only state CB400.

 

My query is how do i know that the bike is really Vtech 1 as it been respray B4?

 

Thanks

[KerplunkZ]

Knowing the correct spec of the Bike

 

Told by previous owner this S4 is VTech1 but when i see the log card it only state CB400.

 

My query is how do i know that the bike is really Vtech 1 as it been respray B4?

 

Thanks

 

Wat plate? Any hiss? Got any fuel knob?

[lauhs8]

Wat plate? Any hiss? Got any fuel knob?

 

1. FT Plate

2. Dont know how to see hv Honda Ignition Security System or not.

3. No fuel Knob.

 

Thanks Bro

[pyro13]

Knowing the correct spec of the Bike

 

Told by previous owner this S4 is VTech1 but when i see the log card it only state CB400.

 

My query is how do i know that the bike is really Vtech 1 as it been respray B4?

 

Thanks

 

Hiss, ter will be a blinking red light wen u off the bike at the meter. U can try goin bikewerkz for the meter

[lauhs8]

Hiss, ter will be a blinking red light wen u off the bike at the meter. U can try goin bikewerkz for the meter

 

If i'm not wrong Vtech 1 don't hv HISS rite?

[pyro13]

If i'm not wrong Vtech 1 don't hv HISS rite?

 

Yeap.. Dun have