[Group] Super Four Non-VTEC Family: PB1 VerR & VerS

[fabian]

If this is true..mannn!..its expensive unless you can find a scraped bike block. Can you make it in the daytime..weekday? PM you my contact.

 

Ah Pek, would try to make it on weekday, daytime.

But think you forgot to PM me your contact.

 

Which part of SG do you stay?

 

Pending on this thursday afternoon.(would you be available?)

[Ah Pek]

Ah Pek, would try to make it on weekday, daytime.

But think you forgot to PM me your contact.

 

Which part of SG do you stay?

 

Pending on this thursday afternoon.(would you be available?)

 

Alamak!...I tot from your previous post someone confirmed your block spoiled liao. Ok..pm liao. Thurs afternoon should be fine at about 2:00 pm.

[norishimu]

spoil block? gulps..

 

anyway my idling kinda low on start up nowadays..

i hv to throttle a little on hold on to it when starting my bike..

otherwise it'll jus die off..

any remedy? adjust idling? centre of carbs am i right?

[Ah Pek]

spoil block? gulps..

 

anyway my idling kinda low on start up nowadays..

i hv to throttle a little on hold on to it when starting my bike..

otherwise it'll jus die off..

any remedy? adjust idling? centre of carbs am i right?

 

This is inevitable...things that move and works never stay the same.

 

Try the following..

 

1) air filter is as clean as be

 

2) Cleaner that mixes with fuel (Valve and jet nozzle Cleaner)

 

3) Eo..try my blend if you like..instant chnage felt!

 

4) Improve your CCA for spark plug.

 

5) Grounding (a MUST HAVE but must be done right)

[norishimu]

gotta try ur special blend and do grounding..

[xiaobanz]

Wanna ask. A lot of pple say they have done grounding. Can i ask what does ground do and how it helps? Cos if it's good, then i think i'll have to go do mine too..

[Ah Pek]

Wanna ask. A lot of pple say they have done grounding. Can i ask what does ground do and how it helps? Cos if it's good, then i think i'll have to go do mine too..

 

It's good provided if it's done right. Basically, it helps in maximizing your battery CCA (Cold Cranking Current best describe as the energy of the battery that provides the electrical load provider)to the spark plug. You want even better..get EPS Charge booster for higher CCA.

[norishimu]

any gd plc to do grounding?

[Ah Pek]

any gd plc to do grounding?

 

There used to be a thread here soley just about grounding where many photos are shown with step by step procedures. Not sure what happened to it though.

[norishimu]

found it..

http://www.singaporebikes.com/forums/showthread.php?t=112145&highlight=grounding&page=7

 

its a 5point grounding..

where n which is the 6th point?

[Ah Pek]

found it..

http://www.singaporebikes.com/forums/showthread.php?t=112145&highlight=grounding&page=7

 

its a 5point grounding..

where n which is the 6th point?

 

Way back, someone started the term "points" here when grounding for bikes were mentioned I think. In truth, "points" especially "5 points" are referred to to cars grounding and wires use are 6 gauge not 8.

 

For bikes, 8 gauge wiring cable is enough and there is no such things reference to as "points"..IMHO. Its circuitry pattern..and its what call "Delta Star Looping". I have seen works done by some mototiam and 'calculating' it, its what I call "Delta Star" without the loop much like the way its done in car. Yes, there are explanation to this but am not doing it here as there are business going on here in this field that would caused arguement about the "method" and way its done.

 

Most works done I have seen oso never have the various earth tapping point terminated correctly or wrong material used. Those that have their grounding done by me understand but again, I cannot say it here to avoid argument. Overall and generally, it does have an improvement effect but the question is, is the grounding up to its full potential? Regard is as a "half a loaf better than non stingy if you want.

 

So before you go spend $s that you find cheap..you have to asked the mototiam people to explain to you why its done that way and "how come" (hardest to answer..LOL!).

 

In short...no 6 points. If you count points..mine is anytime 8 points to 16 points and not every bike is the same..as it's subjected to the make and condition.

[Ah Pek]

Talking about grounding..any vehicle that uses ECU, good quality grounding is a MUST..yes, especially Revo as far as S4 is concern.

[WRfreak]

hi ahpek... remember me... lolx.. i asked u to reserve the EPs.. lolx.. my bike is getting better lolx.. much faster pick up .. anyway.. thx again.. i will get back to u soon.. by the end of the month to adjust the grouding i alreadi have the pdf.. but i still dun get it.. anyway.. another question for all ... i saw this cb900 hornet.. havin this headlight like the cb1000r new wan.. looks nice ... can i noe where to get that headlight..everyone? anyone? not the LAB wan.. but from the cb1000r. i think most prob he took it from tat bike.. lolx.. i have no idea.

[Ah Pek]

hi ahpek... remember me... lolx.. i asked u to reserve the EPs.. lolx.. my bike is getting better lolx.. much faster pick up .. anyway.. thx again.. i will get back to u soon.. by the end of the month to adjust the grouding i alreadi have the pdf.. but i still dun get it.. anyway.. another question for all ... i saw this cb900 hornet.. havin this headlight like the cb1000r new wan.. looks nice ... can i noe where to get that headlight..everyone? anyone? not the LAB wan.. but from the cb1000r. i think most prob he took it from tat bike.. lolx.. i have no idea.

 

Remember you?..of course lah:cheeky: Good that what I do works for you. The two unit of EPS has been taken already but its ok..can get if you want but just don't get it oiutside yourself as it cost so much more $s.

 

Oh yes, the grounding you had...yah, its wrongly done. Will make corrective measure with extra wiring to it and add in the termination block.

 

Wah..CB1000r headlite arh!?..you wanna be extra brite or xtra Garang..LOL!

[WRfreak]

lolx.. maybe a little both haha.. garang and bright.. lolx.. looks nice though.. but dunno where to get it?

[norishimu]

i am lookin fr that headlight too..

[xiaobanz]

Guys today when i was riding, i find that when i about the make a turn and shift my body weight a bit. I find that the handle bar will like turn by itself. i mean of cuz that's normal, but then it is like it's heavier then usual. Shouldn't the handle be normally light as it when during turning, i have to use slightly more strength to keep the handle bar from turning too much.

 

Another thing is when i change to higher gear, the gear changing sound is a little loud though i wearing FF. Cos i juz bought the bike and haven changed EO.. Does EO have an effect for smoother gear change?

 

Or is it maybe i ride my x1 too much le.. hmm..

[MazzyMan]

Guys today when i was riding, i find that when i about the make a turn and shift my body weight a bit. I find that the handle bar will like turn by itself. i mean of cuz that's normal, but then it is like it's heavier then usual. Shouldn't the handle be normally light as it when during turning, i have to use slightly more strength to keep the handle bar from turning too much.

 

Another thing is when i change to higher gear, the gear changing sound is a little loud though i wearing FF. Cos i juz bought the bike and haven changed EO.. Does EO have an effect for smoother gear change?

 

Or is it maybe i ride my x1 too much le.. hmm..

 

Assuming your cone bearings are ok...try tightening them a little more...helped in my case.

 

Yup new and good EO does help in gear changes.

[Ah Pek]

Guys today when i was riding, i find that when i about the make a turn and shift my body weight a bit. I find that the handle bar will like turn by itself. i mean of cuz that's normal, but then it is like it's heavier then usual. Shouldn't the handle be normally light as it when during turning, i have to use slightly more strength to keep the handle bar from turning too much.

 

Another thing is when i change to higher gear, the gear changing sound is a little loud though i wearing FF. Cos i juz bought the bike and haven changed EO.. Does EO have an effect for smoother gear change?

 

Or is it maybe i ride my x1 too much le.. hmm..

 

Perhaps you might want to try my blended eo for your next eo change and let us know?

[xiaobanz]

Perhaps you might want to try my blended eo for your next eo change and let us know?

 

Haha Ah pek i really dun mind... Or if can after my exams will go down and meet you for a coffee then use your blend and try.. Haha..

 

Btw where to tighten the steering cone?? Maybe i really need to tighten.. Cos today when i'm making a sharp right turn, need to use a fair amount of strength to pull back the bike. No a good sign during U-turn.

[xiaobanz]

Oh ya another qns, where can i search for original head light(2nd hand). Cos i ask bike shops they only have the new spec3 headlight which cos $130 w installation. I'm using the rxz headlight which i don't really fancy much cos i love superfour with the original headlight. Tried asking for trade which not many pple wans. SooOOooo hard to find..

[Ah Pek]

Haha Ah pek i really dun mind... Or if can after my exams will go down and meet you for a coffee then use your blend and try.. Haha..

 

Btw where to tighten the steering cone?? Maybe i really need to tighten.. Cos today when i'm making a sharp right turn, need to use a fair amount of strength to pull back the bike. No a good sign during U-turn.

 

LOL!...mine cheap oil but once tried...Ultra Mecee_ma or Mooo_2 give you oso you don't want.

 

As for your Spec3 headlamp at $130..me think its not original. The last I heard was $300+. My PB1 already $200+ complete.

[xiaobanz]

Really that ex??? Wa then like that must try going scrap yards to find.. Heard there have some parts really good condition..

[Burnout69]

LOL!...mine cheap oil but once tried...Ultra Mecee_ma or Mooo_2 give you oso you don't want.

 

As for your Spec3 headlamp at $130..me think its not original. The last I heard was $300+. My PB1 already $200+ complete.

 

Yupzz spec 3 headlight at 130 bux its not original.. original its by stanley, the aftermarket is cdmc sumtin.. im using the aftermarket one.. so far so gd..

[pufferfis]

If you have intention to keep the bike long, its worth getting a new hardness done for $380 or so. Have to do mine soon. Wires also all aged liao...sighhh.

 

 

yoo ah pek..my meter lights n fuel gauge ok now...went to ah chong...fixed the harness there..some bunch of wires wic he redo...i dont tink i cld have found the fault without his help...

 

now to figure out why my coolin system is boiling after i ride hard for half an hr even after i have top up with coolant and around 4 mths ago change to a coolant pump n got a new a coolent cap from ah boy jus last week..the thailand made one from ah boy...