[Discussion] Super Four General Enquiry Thread

[AEoM]

But can start ley...maybe the batt going to die soon uh...not enuff volts during cranking tats y uh....tanx tiku...

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

 

Coil dying bro. Just change mine last mth due to the same reason. I change mine at unique motor for ard $500.

[syeDsTp]

Could be ur starter carbon den...coz i remembered ah pek saying if no cranking push ur bike den engage gear den neutral back and try cranking...if can crank means something to do with starter carbon...

 

Btw my fren riding spec 3,as i noe spec 3 meter needles will turn when switched on to initialize...but his aft the initialization,he crank start the bike & the meter needle turned again.any idea y???

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

 

Bro any idea how much to change to a new starter carbon? Thx for the advise bro..

 

Sent from my GT-N7000 using Tapatalk

[huairen]

Hi... anyone knows where i can get the GIVI windshield for super4?

or anybody selling?

Please PM me.

Thank you!

[tiku]

post deleted

[STRYKER]

Bro any idea how much to change to a new starter carbon? Thx for the advise bro..

 

Sent from my GT-N7000 using Tapatalk

 

Not too sure but abt $120 i guess...coz i also nvr change b4...wad i did was to knock on the starter carbon b4 cranking...if still cannot den i just push start...heheheh

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

[syeDsTp]

What u mean by knock? I still need to push then can start.

 

Sent from my GT-N7000 using Tapatalk

[STRYKER]

What u mean by knock? I still need to push then can start.

 

Sent from my GT-N7000 using Tapatalk

 

Knock as in u take a screw driver or spannar n give the starter carbon a few knocks to free it from jamming. But knocking is only a temporary solution...best to get it changed lah.

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

[syeDsTp]

The starter carbon gt a cable attached to it right?

 

Sent from my GT-N7000 using Tapatalk

[STRYKER]

The starter carbon gt a cable attached to it right?

 

Sent from my GT-N7000 using Tapatalk

 

Yup left side of the bike just above ur coils...

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

[repek666]

hi . can i ask which bike shop do valve clearance on the spot? and how much

 

Sent from my GT-I9100 using Tapatalk 2

[STRYKER]

hi . can i ask which bike shop do valve clearance on the spot? and how much

 

Sent from my GT-I9100 using Tapatalk 2

 

Doubt they can complete it in one day.

What i did was first to change my timing chain,tensioner & camcover o ring in one day.

Den i went over another day to get them to balance my shims in abt 6 hrs.

But i did not changed engine oil or coolant when i did both servicing...

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

[repek666]

okae which shop?? planet??? n hw much???

 

Sent from my GT-I9100 using Tapatalk 2

[repek666]

okae which shop?? planet??? n hw much???

 

Sent from my GT-I9100 using Tapatalk 2

[STRYKER]

okae which shop?? planet??? n hw much???

 

Sent from my GT-I9100 using Tapatalk 2

 

I did my cbr1100xx at global.

Timing chain,tensioner & camcover o ring is $250.

Balancing of the shims is $120.

But its best to make an appt with them so tat they will be prepared...

 

 

}STRYKER{ sent this post via iPhone using Tapatalk

[kok_07]

Hi, I just bought a spec 1. When moving off den got some problem. bike power like stuck stuck den awhile ok. Idling at 1.5 after awhile it decrease den engine die off. Wat is the problem that u all knw? Mechanic told me is carb problem. Dirty and need tunning? Is it true?

[repek666]

yep2 it carb.. dirty n many things inside shd be wear n tear n nid to change.. done at unique... cost me $200..

 

Sent from my GT-I9100 using Tapatalk 2

[holdurhead]

Hi when my vtec open got black smoke, friend day exhaust got too much carbon. How to remove them?

[stwb1981]

Hi, I just bought a spec 1. When moving off den got some problem. bike power like stuck stuck den awhile ok. Idling at 1.5 after awhile it decrease den engine die off. Wat is the problem that u all knw? Mechanic told me is carb problem. Dirty and need tunning? Is it true?

 

Refer to the non vtec thread.... my experience wif my bike is there...

 

Hi when my vtec open got black smoke, friend day exhaust got too much carbon. How to remove them?

 

simple juz ride harder...!!!

do note it doesn't mean U gt to travel @ high speed or clear meter...

Rather U can high rev from gear 1 onwards...

Carbon oso clear...

Safest go NSHW & clear... Singapore own risk...

BUT DO SO AT YR COMFY PACE...

[Nick87]

Hi all any JB shop to intro can do vtec 3 well

[stwb1981]

Hi all any JB shop to intro can do vtec 3 well

 

Do what things mate??

 

I going in later to ah qua lane there to my regular shop then...

 

If basic change eo, plug etc shouldn't b a prob...

if top overhaul or more complex stuff...

My $$$ is in Sg...

 

Cheers!!!

[ahso0n]

Any fellow rider know the price of second hand LV SBK endcan?

[Nick87]

Plug can change in jb which shop

[stwb1981]

Plug can change in jb which shop

 

Pricing wise.... I rather change in sg... not worth....

WK motorsport have....

think most shop have lah....

try the ones @ ah qua lane... (sadly that the only place i noe..lol)

[Arlwynn]

Hi guys just to inform that i have these few Revo items for sale ...

 

1- Original Bagster Tankbra for Revo, Silver Wing Tribal Edition. ( Used )( Good Condition ) ( $120 )

2- Gi-Pro DS Series Gear Indicator For Revo "PNP" NO Wire Cutting or Spicing of Wire.

( Used )( Red Colour Indicator ) ( $150 )

3- "NEW" Front Fork Axle Slider ( $55 )

4- "NEW" VoltMeter ( $35 )

5- "NEW" NGK IridiumIX Spark Plugs "CR8EHIX-9" X 4 NO.S ( $48 )

 

All items in Good and Working Condition : 9/10

Any further Information can PM me ...

Edited July 8, 2012 by Arlwynn

[jimmmmmy]

Hi, anyone of you knw the trade in price for spec 1 nowadays?